background image

SPECIFICATIONS

Voltage:  

18V

No Load Speed:  

 0-2300/min

Chuck Size: 

 6.35mm (1/4”) Hex

Impact Rate: 

 0-2900/min

Max. Torque: 

 150Nm

Weight:  

1.4kg

CORDLESS

IMPACT DRIVER

INSTRUCTION MANUAL

ozito.com.au

WHAT’S IN THE BOX

Impact Driver

PXDDK-301

IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU 

MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS 

WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO 

RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE 

OUR CUSTOMER SERVICE HELPLINE:

Australia 1800 069 486
New Zealand 0508 069 486

WARRANTY

TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL 

NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER 

SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND 

ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE 

WARRANTY POLICY OR PROCEDURE.

OZITO 

Australia/New Zealand (Head Office)

 

1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.

The benefits provided under this warranty are in addition to other rights and 
remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to 
a replacement or refund for a major failure and for compensation for any other 
reasonably foreseeable loss or damage. You are also entitled to have the goods 
repaired or replaced if the goods fail to be of acceptable quality and the failure 
does not amount to a major failure. 
Generally you will be responsible for all costs associated with a claim under this 
warranty, however, where you have suffered any additional direct loss as a result of 
a defective product you may be able to claim such expenses by contacting our 
customer service helpline above.

0316

WARNING

The following actions will result in the warranty being 

void.

• 

 If the tool has been operated on a supply voltage other than that specified 

on the tool.

• 

 If the tool shows signs of damage or defects caused by or resulting from 

abuse, accidents or alterations.

• 

 Failure to perform maintenance as set out within the instruction manual.

• 

 If the tool is disassembled or tampered with in any way.

5 YEAR REPLACEMENT WARRANTY

Your Product is guaranteed for a period of 60 months from the original date of 
purchase and is intended for DIY (Do It Yourself) use only. If a product is defective it 
will be replaced in accordance with the terms of this warranty. 

Lithium Ion 

batteries and chargers are covered by a 36 month 
warranty

 and are excluded from the warranty extension. Warranty excludes 

consumable parts.

Summary of Contents for PXDDK-301















Reviews: