background image

Owner’s Manual

M7500-PRO

POWER FILTRA

TION AND REGULA

TION ACTIVE                                       HIGH CURRENT

 GROUND

ISOLATION

ACTIVE

BANK 1 ON       BANK 2 ON       BANK 3 ON       BANK 4 ON          BANK 5              BANK 5 

 HC 1 ON           HC 2 ON

BRIGHTNESS 

PRESS: 

METER SELECT

Home Theater P

ower Management

AUTO

1690 Corporate Circle, Petaluma CA 94954  •  www.panamax.com

MODEL: M7500-PRO

Thank you for purchasing this MAX

®

7500-PRO

Home Theater Power Management! You now own

one of the finest line conditioning, regulating and

power protection products on the market today.

Over 30 years of power protection experience and

more than 15 years of Audio/Video noise filtra-

tion experience were utilized during the develop-

ment of this model.    

The MAX

®

7500-PRO has been specifically engi-

neered to enhance the performance and life

expectancy of high-end Audio/Video entertain-

ment gear. The combination of our sophisticated

power conditioning and the world’s finest power

protection has resulted in an Audio/Video power

center that meets the power quality needs for each

piece of equipment in your entertainment system.

This is truly a Firewall for Noise™!  With power

this clean, your audio/video or home theater sys-

tem will finally be able to perform up to its full

capabilities.  Performance alone makes this a

world-class product but we didn’t stop there; its

styling complements and completes even the

most sophisticated Audio/Video showcase.

MAX

®

7500-PRO

HOME THEATER POWER MANAGEMENT

INS7500 REV. C      9/06

Summary of Contents for MAX 7500-PRO


















Reviews: