Accessories
Operating Instructions
(English
: YFM284C454ZA)
(Deutsch
: YFM284C455ZA)
(Français
: YFM284C456ZA)
(Nederlands : YFM284C457ZA)
(Svenska
: YFM284C458ZA)
(Italiano
: YFM284C459ZA)
(Español
: YFM284C460ZA)
(Dansk
: YFM284C461ZA)
Q'ty: 1 set
Installation Instructions
(English, Deutsch, Français,
Nederlands
: YFM284C466ZA)
(Svenska, Italiano, Español,
Dansk
: YFM284C467ZA)
Q'ty: 1 set
Warranty Card
Q'ty: 1
Lock Cancel Plate
(FX0214C385ZA)
Q'ty: 2
Mounting Bolt
(YEJV014C002N)
Q'ty: 1
Mounting Collar
(FX0214C384ZA)
Q'ty: 1
Trim Plate
(YFC054C079ZA)
Q'ty: 1
Power Connector
(YEAJ02874)
Q'ty: 1
Notes:
¡
The number in parentheses underneath
each accessory part name is the part
number for maintenance and service.
¡
Accessories and their part numbers are
subject to modification without prior
notice due to improvements.
¡
Mounting Collar and Trim Plate are
mounted on the main unit at shipment.
CD Player/Receiver
CQ-C1021NW/C1011NW/C1001NW
Operating Instructions
¡
Please read these instructions carefully before using this product and keep this manual for future reference.
CQ-C1021N
MUTE/SQ
RANDOM
SCAN
REPEAT
TA
V
O
L
U
M
E
T
U
N
E
/T
R
A
C
K
R
EG
MO
NO
LOC
BAND
1
2
3
4
5
6
PWR
CT
SRC
DISP
APM
D·M
D·M
SEL
SEL
SEL
PTY
AF
(CQ-C1021NW)
Specifications
YFM284C454ZC TAMACO1004-2055 Printed in China
General
Power Supply
: 12 V DC (11 V – 16 V), Negative
Ground
Tone Controls (Bass)
: ±12 dB (100 Hz)
Tone Controls (Treble)
: ±12 dB (10 kHz)
Current Consumption
: Less than 2.5 A (CD mode, 0.5 W
4 channels)
Maximum Power Output
: 45 W x 4 (4
Ω
)
Speaker Impedance
: 4 – 8
Ω
Pre-Amp Output Voltage
: 2.5 V (CD mode, 1 kHz, 0 dB)
Pre-Amp Output Impedance
: 200
Ω
Dimensions (Main Unit)
: 178(W) x 50(H) x 160(D) mm
Weight (Main Unit)
: 1.3 k
g
CD Player
Sampling frequency
: 8 times oversampling
DA converter
: 1 bit DAC System
Pick-up type
: Astigma 3-beam
Light source
: Semiconductor laser
Wave length
: 790 nm
Frequency response
: 20 Hz – 20 kHz (±1 dB)
Signal to noise ratio
: 96 dB
Total harmonic distortion
: 0.01 % (1 kHz)
Wow and flutter
: Below measurable limits
Channel separation
: 75 dB
FM Stereo Radio
Frequency Range
: 87.5 MHz – 108 MHz
Usable Sensitivity
: 6 dB/µV (S/N 30 dB)
Stereo Separation
: 35 dB (1 kHz)
AM (MW) Radio
Frequency Range
: 531 kHz – 1 602 kHz
Usable Sensitivity
: 28 dB/µV (S/N 20 dB)
AM (LW) Radio
Frequency Range
: 153 kHz – 279 kHz
Usable Sensitivity
: 32 dB/µV (S/N 20 dB)
Notes:
¡
Specifications and design are subject to modification without
notice due to improvements.
¡
Some figures and illustrations on this manual may be different
from real ones.
Matsushita Electric Industrial Co., Ltd.
Web Site: http://www.panasonic.co.jp/global/
English
Before Reading These Instructions
Panasonic welcomes you to our constantly growing family of electronic products owners.
We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured with carefully selected components, and
assembled by people who are proud of the reputation their work has built for our company. We know this product will bring you many hours of
enjoyment, and after you discover the quality, value and reliability we have built into it, you too will be proud to be a member of our family.
Laser Product
Differences among 3
models
This operating instruction manual is for 3 models CQ-C1021NW, CQ-C1011NW and CQ-C1001NW. All illustrations throughout
this manual represent model CQ-C1021NW unless otherwise specified. The following table describes the differences among 3
models.
Label Indications and Their Locations
CAUTION
LASER RADIATION WHEN OPEN. DO NOT STARE
INTO BEAM.
Caution
This product utilizes a laser.
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
Do not take apart this unit or attempt to
make any changes yourself.
This unit is a very intricate device that uses a laser
pickup to retrieve information from the surface of
compact discs. The laser is carefully shielded so that
its rays remain inside the cabinet.
Therefore, never try to disassemble the player or alter
any of its parts since you may be exposed to laser
rays and dangerous voltages.
CLASS 1 LASER PRODUCT
Caution Label
Deck Ass’y (in the unit,
upper side)
Preparation
The 24-hour system is used for the clock.
Notes:
¡
Adjust the clock when “NO CT” appears on the dis-
play.
¡
When a broadcast of FM Radio Data System is
received, the clock is set automatically by the CT
(Clock Time) service.
¡
Hold down
[
]
]
or
[
[
]
to change numbers rapidly.
1
Select the radio AM mode.
(
a
“Radio (AM [LW/MW]/FM)”)
2
Hold down
[DISP] (CT)
for more than 2
seconds.
Hour blinks
3
Adjust the hour.
Hour entered
[
[
]
: sets the hour ahead.
[
]
]
: sets the hour back.
4
Press
[DISP] (CT)
.
Minute blinks
5
Adjust the minute.
Minute entered
[
[
]
: sets the minute ahead.
[
]
]
: sets the minute back.
6
Press
[DISP] (CT)
.
Completed
Clock Setting
Features
Models
CQ-C1021NW
CQ-C1011NW
CQ-C1001NW
Display colour
Blue
Black
Black
Key/disc slot illumination colour
Red
Red
Green
Maintenance
Your product is designed and manufactured to ensure the minimum of maintenance. Use a soft cloth for routine
exterior cleaning. Never use benzine, thinner, or other solvents.
Cleaning the
Unit
Fuse
Anti-Theft System
This unit is equipped with a removable face plate. Removing this face plate makes the unit totally inoperable.
Removing
1
Turn off the power.
2
Press
[
]
. The face plate will open.
3
Pull it out toward you.
Mounting
1
Slide the left side of the face plate in
place.
2
Press the right end of face plate until a
“click” is heard.
Caution
¡
This face plate is not waterproof. Do not expose it to
water or excessive moisture.
¡
Do not remove the face plate while driving your car.
¡
Do not place the face plate on the dashboard or nearby
areas where the temperature rises high.
¡
Do not touch the contacts on the face plate and the
main unit, since this may result in poor electrical con-
tact.
¡
If dirt or other foreign substances get on the contacts,
wipe them off with a clean and dry cloth.
Face Plate Removing/Mounting
(Anti-Theft System)
If the replaced fuse fails, contact your nearest authorized Panasonic Service Centre.
Warning
¡
Use fuses of the same specified rating (15 A). Using substitutes or fuses with higher ratings, or connecting the unit
directly without a fuse could cause fire or damage to the unit. If the replaced fuse fails, contact your nearest author-
ized Panasonic Service Centre.
Troubleshooting
Trouble
Check point
No power
●
Start the engine. (Or turn the ignition
switch to the ACC position.)
●
Verify the wiring. (Ex. battery lead,
power lead, ground lead, etc.)
●
Fuse blown (Contact the nearest
Panasonic Service Centre.)
●
Ask a professional for fuse replace-
ment.
●
Be sure to use the same rated fuse.
No sound
●
Disable the mute function.
●
Verify the wiring.
●
Wait until the dew disappears before
turning on the unit.
Noise
●
Make sure that grounding is established
properly.
Common
Frequent
noise
●
Tune into another station of high-inten-
sity waves.
●
Make sure that the antenna mounted
point is grounded properly.
Radio
Preset data
deleted
●
The preset memory is cleared to return
to the original factory setting when the
power connector or battery is discon-
nected.
No sound, or disc
is automatically
ejected
●
Load the disc correctly.
●
Clean the disc.
Disc Player
Sound skip,
poor sound
quality
●
Clean the disc.
Sound skip
due to
vibration
●
The maximum permissible tilt angle is
30°.
●
Secure the unit.
Disc not
ejectable
●
Press
[
u
]
. If the disc is still not eject-
ed, contact the nearest Panasonic
Service Centre.
No sound from
left, right, front,
or rear speaker
●
Adjust the balance and fader.
●
Verify the wiring.
Trouble
Check point
Left and right
sounds are
reversed
●
Connect the speaker lead correctly.
Error Display Messages
(The disc is ejected automatically.)
The disc is dirty, or is upside down.
The disc has scratches.
●
Check the disc.
No operation by some cause.
●
If normal operation is not restored, call
the store where you purchased the unit
or the nearest Panasonic Service
Centre to ask for repairs.
If You Suspect Something Wrong
Check and take steps as described below.
If the described suggestions do not solve the problem, it is recom-
mended to take the unit to your nearest authorized Panasonic Service
Centre. The product should be serviced only by qualified personnel.
Please refer the checking and the repair to professionals. Panasonic
shall not be liable for any accidents arising out of neglect of checking
the unit or your own repair after your checking.
Warning
¡
Do not use the unit in an irregular condition, for example, with-
out sound, or with smoke or a foul smell, which can cause
ignition or electric shock. Immediately stop using the unit and
consult your dealer.
¡
Never try to repair the unit by yourself because it is dangerous
to do so.
2
1
2
1
Safety Information
Warning
Observe the following warnings when using this
unit.
❑
The driver should neither watch the display nor operate
the system while driving.
Watching the display or operating the system will distract the driv-
er from looking ahead of the vehicle and can cause accidents.
Always stop the vehicle in a safe location and use the parking
brake before watching the display or operating the system.
❑
Use the proper power supply.
This product is designed for operation with a negative grounded
12 V DC battery system. Never operate this product with other bat-
tery systems, especially a 24 V DC battery system.
❑
Protect the Deck Mechanism.
Do not insert any foreign objects into the slot of this unit.
❑
Do not disassemble or modify the unit.
Do not disassemble, modify the unit or attempt to repair the prod-
uct yourself. If the product needs to be repaired, consult your
dealer or an authorized Panasonic Service Centre.
❑
Do not use the unit when it is out of order.
If the unit is out of order (no power, no sound) or in an abnormal
state (has foreign objects in it, is exposed to water, is smoking, or
smells), turn it off immediately and consult your dealer.
❑
Refer fuse replacement to qualified service personnel.
When the fuse burns out, eliminate the cause and have it replaced
with the fuse prescribed for this unit by a qualified service engi-
neer. Incorrect replacement of the fuse may lead to smoke, fire,
and damage to the product.
Observe the following warnings when installing.
❑
Disconnect the lead from the negative (–) battery termi-
nal before installation.
Wiring and installation with the negative (–) battery terminal con-
nected may cause electrical shock and injury due to a short circuit.
Some cars equipped with the electrical safety system have specific
procedures of battery terminal disconnection.
FAILURE TO FOLLOW THE PROCEDURE MAY LEAD TO THE
UNINTENDED ACTIVATION OF THE ELECTRICAL SAFETY SYSTEM
RESULTING IN DAMAGE TO THE VEHICLE AND PERSONAL
INJURY OR DEATH.
❑
Never use safety-related components for installation,
grounding, and other such functions.
Do not use safety-related vehicle components (fuel tank, brake,
suspension, steering wheel, pedals, airbag, etc.) for wiring or fix-
ing the product or its accessories.
❑
Installing the product on the air bag cover or in a location
where it interferes with airbag operation is prohibited.
❑
Check for piping, gasoline tank, electric wiring, and other
items before installing the product.
If you need to open a hole in the vehicle chassis to attach or wire
the product, first check where the wire harness, gasoline tank, and
electric wiring are located. Then open the hole from outside if pos-
sible.
❑
Never install the product in a location where it interferes
with your field of vision.
❑
Never have the power cord branched to supply other
equipment with power.
❑
After installation and wiring, you should check the nor-
mal operation of other electrical equipment.
The continuation of their using in abnormal conditions may cause
fire, electrical shock or a traffic accident.
❑
In the case of installation to an airbag-equipping car,
confirm warnings and cautions of the vehicle manufactur-
er before installation.
❑
Make sure the leads do not interfere with driving or get-
ting in and out of the vehicle.
❑
Insulate all exposed wires to prevent short circuiting.
Caution
Observe the following cautions when using this
unit.
❑
Keep the sound volume at an appropriate level.
Keep the volume level low enough to be aware of road and traffic
conditions while driving.
❑
This unit is designed for use exclusively in automo-
biles.
❑
Do not operate the unit for a prolonged period with the
engine turned off.
Operating the audio system for a long period of time with the
engine turned off will drain the battery.
❑
Do not expose the unit to direct sunlight or excessive
heat.
Otherwise these will raise the interior temperature of the unit,
and it may lead to smoke, fire, or other damage to the unit.
❑
Do not use the product where it is exposed to water,
moisture, or dust.
Exposure of the unit to water, moisture, or dust may lead to
smoke, fire, or other damage to the unit. Make especially sure
that the unit does not get wet in car washes or on rainy days.
Observe the following cautions when installing.
❑
Refer wiring and installation to qualified service per-
sonnel.
Installation of this unit requires special skills and experience. For
maximum safety, have it installed by your dealer. Panasonic is
not liable for any problems resulting from your own installation
of the unit.
❑
Follow the instructions to install and wire the product.
Not following the instructions to properly install and wire the
product could cause an accident or fire.
❑
Take care not to damage the leads.
When wiring, take care not to damage the leads. Prevent them
from getting caught in the vehicle chassis, screws, and moving
parts such as seat rails. Do not scratch, pull, bend or twist the
leads. Do not run them near heat sources or place heavy objects
on them. If leads must be run over sharp metal edges, protect
the leads by winding them with vinyl tape or similar protection.
❑
Use the designated parts and tools for installation.
Use the supplied or designated parts and appropriate tools to
install the product. The use of parts other than those supplied or
designated may result in internal damage to the unit. Faulty
installation may lead to an accident, a malfunction or fire.
❑
Do not block the air vent or the cooling plate of the unit.
Blocking these parts will cause the interior of the unit to over-
heat and will result in fire or other damage.
❑
Do not install the product where it is exposed to strong
vibrations or is unstable.
Avoid slanted or strongly curved surfaces for installation. If the
installation is not stable, the unit may fall down while driving and
this can lead to an accident or injury.
❑
Installation Angle
The product should be installed in a horizontal position with the
front end up at a convenient angle, but not more than 30˚.
The user should bear in mind that in some areas there may be
restrictions on how and where this unit must be installed.
Consult your dealer for further details.
❑
Wear gloves for safety. Make sure that wiring is com-
pleted before installation.
❑
To prevent damage to the unit, do not connect the
power connector until the whole wiring is completed.
❑
Do not connect more than one speaker to one set of
speaker leads. (except for connecting to a tweeter)
This pictograph intends to alert you to the presence of
important operating instructions and installation instruc-
tions. Failure to heed the instructions may result in
severe injury or death.
■
Read the operating instructions for the unit and all other compo-
nents of your car audio system carefully before using the system.
They contain instructions about how to use the system in a safe and
effective manner. Panasonic assumes no responsibility for any prob-
lems resulting from failure to observe the instructions given in this
manual.
■
This manual uses pictographs to show you how to use the product
safely and to alert you to potential dangers resulting from improper
connections and operations. The meanings of the pictographs are
explained below. It is important that you fully understand the mean-
ings of the pictographs in order to use this manual and the system
properly.
Warning
This pictograph intends to alert you to the presence of
important operating instructions and installation instruc-
tions. Failure to heed the instructions may result in
injury or material damage.
Caution
Sales and Support Information
For UK and Ireland customers only.
Customer Care Centre
¡
For customers within the UK: 08705 357357
¡
For customers within the Republic of Ireland: 01 289 8333
¡
Visit our website for product information
¡
E-mail: customer.care@panasonic.co.uk
Direct Sales at Panasonic UK
¡
Order accessories and consumable items for your product
with ease and confidence by phoning our Customer Care
Centre Monday - Thursday 9:00am - 5:30pm, Friday
9:30am - 5:30pm. (Excluding public holidays).
¡
Or go on line through our Internet Accessory ordering
application at www.panasonic.co.uk.
¡
Most major credit and debit cards accepted.
¡
All enquiries, transactions and distribution facilities are
provided directly by Panasonic UK Ltd.
¡
It couldn't be simpler!
¡
Also available through our Internet is direct shopping for a
wide range of finished products, so take a browse on our
website for further details.
V A R O I T U S – L A S E R -
SÄTEILYVAARA
A V A T T A E S S A . V A R O
ALTISTUMISTA
SÄTEELLE.
FÖRSIKTIGHET –
LASERSTRÅLNING I
ÖPPNAT LÄGE. UNDVIK
ATT UTSÄTTAS FÖR
STRÅLEN.
A D V A R S E L – L A S E R -
S T R Å L I N G . U N N G Å
E K S P O N E R I N G F O R
STRÅLEN VED ÅPNING.
ÇçàåÄçàÖ – ãÄáÖêçéÖ
àáãìóÖçàÖ
èêà
éíäêõíàà. àáÅÖÜÄíú
ÇéáÑÖâëíÇàü ãÄáÖêçéÉé
àáãìóÖçàü.
CAUTION - LASER RA-
DIATION WHEN OPEN.
AVOID EXPOSURE TO
BEAM.
VORSICHT - LASER-
STRAHLUNG, WENN
GEÖFFNET. VERMEIDEN
SIE EIN AUSSETZEN
GEGENÜBER DEM
LASERSTRAHL.
ATTENTION –
RAYONNEMENT LASER
SI OUVERT, ÉVITER
TOUTE EXPOSITION AU
FAISCEAU.
ADVARSEL – LASER
UDSENDES NÅR DER
ER ÅBNET. UNDGÅ
UDSÆTTELSE FOR
STRÅLER.
