background image

Installation Instructions

Model No.

Projector ceiling mount bracket

ET-PAD310

Thank you for purchasing a Panasonic product.

 

To customers

the installation. After the installation and receiving the “Installation Instructions” from the installation personnel, save it for 

future use. When moving or removing the projector, give this manual to the installation personnel to perform the operation.

 

To installation personnel

Read the “Installation Instructions” thoroughly and then perform the operation correctly and safely. Also, always read the 

“Important Safety Notice” on pages 2 and 3 of this manual as they contain important information. After the installation, give 

the “Installation Instructions” to the customer to save for future use.

TQZJ294-3

SS0710KM3047 -KI

Printed in Japan

Contents

Important Safety Notice  ……………………………2
Product description …………………………………3
Standard installation dimensions  …………………4
Removal method  ……………………………………8

Removing the projector  …………………………8

Installation method  …………………………………9

Installing the brackets to the projector  …………9
Suspending the projector  …………………… 10

Adjusting the installation angle  ………………… 11
Attaching the drop prevention set to the ceiling  13

  …………………………………… 13

Summary of Contents for ET-PAD310















Reviews: