background image

ENGLISH

ENGLISH

FRANÇAIS

DEUTSCH

Thank you for purchasing this Panasonic product.

 

To customers

The “Installation Instructions” is intended for use by installation personnel.  Be sure to employ certified personnel to 

perform the installation. 

After installation, have the installation personnel return these “Installation Instructions” to you, and save it for future use. 

When moving or removing the projector, give this manual to the certified personnel and have them perform the procedure.

 

To installation personnel

Read the “Installation Instructions” thoroughly and then perform the operation correctly and safely. 

Be sure to read through the section entitled “Read this first!” (page 3) before proceeding with the installation.

If the separately sold ET-DLE030 Fixed-focus lens will be used with the projector, obtain the “Operating Instructions”for 

the

 

lens from the customer and refer to this manual and the “Installation Instructions” during installation.

After installation, return these “Installation Instructions” to the customer.

*  The figure above shows this product combined with the separately sold ET-PKD130H Ceiling Mount Bracket (for High 

Ceilings, 6-axis Adjustment).

Installation Instructions

Projector Mount Bracket

Model No.   

ET-PKD130B

TQZJ577-7

ET-PKD130B_EN_TQZJ577-7.indd   1

2017/03/13   19:04:50

Summary of Contents for ET-PKD130B



















Reviews: