background image

使用說明書

攪拌機

(家庭用)

目錄
安全注意事項••••••••••••••• 2
零件名稱••••••••••••••••• 6
攪拌機的使用方法••••••••••••• 8
乾式碾磨機的使用方法••••••••••• 11
安全鎖定••••••••••••••••• 14
斷路器保護裝置•••••••••••••• 15
清潔方式••••••••••••••••• 16
疑難排解••••••••••••••••• 18
規格•••••••••••••••••• 封底

感謝您購買 Panasonic 產品。

• 

本產品僅供家庭使用。

• 

請仔細閱讀本說明書,並在使用本產品時遵循安全注意
事項。

• 

在使用本產品前,請特別注意「安全注意事項」(第 2 
頁)。

• 

請確定保證書上載有購買時的日期與商店名稱,並與本
操作說明書共同存放。

Operating Instructions

Blender

 (household use)

Table of Contents

Safety Precautions ••••••••••••••••••••••••••••••••••••••2

Parts Identification ••••••••••••••••••••••••••••••••••••••6

How to Use Blender ••••••••••••••••••••••••••••••••••••8

How to Use Dry Mill •••••••••••••••••••••••••••••••••• 11

Safety Lock ••••••••••••••••••••••••••••••••••••••••••••• 14

Circuit Breaker Protection ••••••••••••••••••••••••••• 15

How to Clean •••••••••••••••••••••••••••••••••••••••••• 16

Troubleshooting ••••••••••••••••••••••••••••••••••••••• 18

Specifications ••••••••••••••••••••••••••••••• Back cover

Thank you for purchasing Panasonic product.

•  This product is intended for household use only.

•  Please read these instructions carefully and follow safety 

precautions when using this product.

•  Before using this product please give your special attention to 

“Safety Precautions” (Page 2).

•  Please make sure the date and name of store of purchase on 

the warranty and keep it with this Operating Instructions.

Model No. 

MX-151SG2/MX-151SP2

0_MX-151SG1-050.indd   1

2010/05/24   11:31:07

Summary of Contents for MX-151SG2





















Reviews: