Panasonic RAMSA WS-AT200 Operating Instructions Manual Download

Page: 1 / 12

Speaker System

WS-AT200

Subwoofer System

WS-AT250

Before attempting to connect or operate this product, please read these instructions completely

CONTENTS

REGULATORY STATEMENTS ............................................................................ 2

SAFETY INSTRUCTIONS .................................................................................... 2

PREFACE ............................................................................................................ 3

PRECAUTIONS ................................................................................................... 3

INSTALLING THE SPEAKER .............................................................................. 4

CONNECTING SPEAKER CABLES .................................................................... 6

WIRING CONNECTOR AND CABLE .................................................................. 7

SETTING THE SUBWOOFER PROCESSOR ....................................................... 8

PROTECTION CIRCUITS FOR WS-AT200 .......................................................... 8

SYSTEM DIAGRAM ............................................................................................ 8

BLOCK DIAGRAM .............................................................................................. 9

SPECIFICATIONS ............................................................................................... 9

TYPICAL PERFORMANCE .................................................................................. 10

DIRECTIVITY ....................................................................................................... 10

APPEARANCE .................................................................................................... 11

WS-AT200

WS-AT250

Summary of Contents for RAMSA WS-AT200













Search results

Summary of Contents for RAMSA WS-AT200

Reviews:

Related manuals for RAMSA WS-AT200

Brands by name

Popular brands

Panasonic RAMSA WS-AT200, Operating Instructions Manual

Search results

Summary of Contents for RAMSA WS-AT200

Reviews:

Related manuals for RAMSA WS-AT200

Brands by name

Popular brands