MP3 CD Player/Receiver
Model:
Operating Instructions
¡
Please read these instructions carefully before using this product and keep this manual for future reference.
Specifications
Accessories
Mounting Collar
Trim Plate
Power Connector Remote Control Unit
(a battery included)
Q’ty: 1
Q’ty: 1
Q’ty: 1
Q’ty: 1
(FX0214C384ZB)
(YFC054C079YA)
(YAJ024C146CA)
(YFX994C199CA)
Lock Cancel Plate Mounting Bolt (5 mm ø) Rubber Bushing Operating Instructions Installation Instructions
Installation kit
Instruction kit
Q’ty: 1 set
Q’ty: 3
Q’ty: 1
(ZZBISCP137U)
(English: YFM264C321CA)
(Français: YFM264C322CA)
(Español: YFM264C323CA)
(YFM294C211CA)
Notes
:
¡
The number in parentheses underneath each accessory part name is the part number for maintenance and ser
-
vice.
¡
Accessories and their part numbers are subject to modification without prior notice due to improvements.
¡
Mounting Collar and Trim Plate are mounted on the main unit at shipment.
General
Power supply:
12 V DC (11 V – 16 V) test voltage
14.4 V, Negative ground
Current consumption:
Less than 2.2 A (CD mode,
0.5 W x 4 channels)
Maximum power output:
50 W x 4 channels (at 1 kHz), Vol-
ume control maximum
Tone adjustment range
Bass:
± 12 dB (at 100 Hz)
Treble:
± 12 dB (at 10 kHz)
Speaker impedance:
4 – 8
Ω
Pre-amp output voltage:
2.0 V (CD mode, 1 kHz, 0 dB)
Pre-amp output impedance:
200
Ω
Dimensions (W x H x D):
178 mm x 50 mm x 158 mm
{7
”
x 1 15/16
”
x 6 1/4
”
}
Weight:
1.3 k
g
{2 lbs. 14 oz}
Front AUX input
Input impedance:
10 k
Ω
Maximum input level:
2.0 V
Connector:
3.5 mm ø Stereo mini pin
Input sensitivity:
200 mVrms
FM radio
Frequency range:
87.9 MHz – 107.9 MHz
Usable sensitivity:
11.0 dBf (75
Ω
)
50 dB quieting sensitivity: 15.2 dBf (75
Ω
)
Frequency response:
30 Hz – 15 kHz (±3 dB)
Alternate channel selectivity:
75 dB
Stereo separation:
35 dB (at 1 kHz)
Image rejection ratio:
55 dB
IF rejection ratio:
100 dB
Signal/noise ratio:
62 dB
AM radio
Frequency range:
530 kHz – 1 710 kHz
Usable sensitivity:
27 dB/µV (22 µV, S/N 20 dB)
CD player
Sampling frequency:
8 times oversampling
DA converter:
1 bit DAC System
Pick-up type:
Astigma 3-beam
Light source:
Semiconductor laser
Wavelength:
790 nm
Frequency response:
20 Hz – 20 kHz (±1 dB)
Signal to noise ratio:
96 dB
Total harmonic distortion: 0.01 % (1 kHz)
Wow and flutter:
Below measurable limits
Channel separation:
75 dB
Above specifications comply with EIA standards.
Notes
:
¡
Specifications and design are subject to modification
without notice due to improvements.
¡
Some figures and illustrations in this manual may be
different from your product.
YFM264C321CA PTW1213-0 Printed in China
Power Output:
16 W RMS x 4 Channels at 4
Ω
and
≤
1%
THD+N
Signal to Noise Ratio:
85 dBA (reference: 1 W into 4
Ω
)
English