background image

 
 

 

 

 

 

 

 

PTRIG™ SETUP MANUAL 

 

PANORICS LLC. ALL RIGHTS RESERVED 

 

ONLY FOR USE WITH PANORICS PRODUCTS 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 

PTRig™ is patent pending. PTRig™ is a trademark of Panorics Corp. All rights reserved. 

PTRig™ is compatible and works with GoPro® Hero4 cameras. GoPro, Hero, the GoPro logo, and the GoPro be a Hero Logo 

are trademarks of GoPro, Inc. GoPro does not endorse, sponsor, approve of, or is in any way associated with PTRig™. If you 

would like to buy GoPro products, please do so through GoPro or an authorized retailer, reseller or distributor. 

By using this PTRig™ product with any of the above-mentioned third party products you take full and sole responsibility for any 

early cancellation and termination of guarantee provided by such third parties or their service providers. PTRig™ takes no direct 

or indirect obligation or liability for any direct or consequential losses, damages to property or moral damages, your self-made 

installation of this PTRig™ product or any damage you can make to it or to any third party product. 

The PTRig™ installation manual is for information purposes only and was not approved or recommended, or included in the 

technical guarantee provided by any third party including but not limited to GoPro, Inc. By purchasing this product you accept 

full responsibility. PTRig™ does not come with any warranty. Panorics Corp. does not have a return policy and all PTRig™ 

products are purchased “as is”.

Summary of Contents for PTRIG














Reviews: