background image

1

INE144-P and INE144-S

IDSL Network Extenders Installation Instructions

Document Number INE1-A2-GN10-00

May 2005

Contents

Software and Firmware License Agreement

.................................................

1

Product Documentation Online

.....................................................................

3

Warranty, Sales, Service, and Training Information

......................................

3

Package Contents

.........................................................................................

3

Unpacking and Inspecting the Equipment.

...................................................

4

Powering Up the INE144

..............................................................................

4

Verifying the Switch Configuration (INE144-P only).

.....................................

5

Connecting the IDSL Line

.............................................................................

5

Connecting the Ethernet Line

.......................................................................

6

LED Indicators 

.............................................................................................

7

EMI Notices

..................................................................................................

9

Important Safety Instructions

........................................................................ 10

Software and Firmware License Agreement 

The terms and conditions of this License Agreement (the “Agreement”) will apply to the 
software and/or firmware (individually or collectively the “Software”) incorporated into 
the Paradyne product (the “Product”) purchased by you and any derivatives obtained 

ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS
TERMS, YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED
INTO THE PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU
SHOW YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.

IN THE EVENT THAT YOU DO NOT AGREE WITH ANY OF THE TERMS OF THIS
LICENSE AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT IN ITS
ORIGINAL PACKAGING AND YOUR SALES RECEIPT OR INVOICE TO THE
LOCATION WHERE YOU OBTAINED THE PARADYNE PRODUCT OR THE
LOCATION FROM WHICH IT WAS SHIPPED TO YOU, AS APPLICABLE, AND YOU
WILL RECEIVE A REFUND OR CREDIT FOR THE PARADYNE PRODUCT
PURCHASED BY YOU.

Summary of Contents for INE144-P













Reviews: