background image

1

SNE2020G-P and SNE2020G-S

2-Port Network Extenders Installation Instructions

Document Number SNE2-A2-GN11-00

September 2004

Contents

Software and Firmware License Agreement

.................................................

1

Package Contents

........................................................................................

3

Connecting to Power

....................................................................................

3

Switchpack Configuration

.............................................................................

4

Connecting the SHDSL Lines

.......................................................................

6

Connecting the Ethernet Line

.......................................................................

8

Ferrite Chokes

..............................................................................................

8

LED Indicators

..............................................................................................

9

EMI Notices

.................................................................................................. 11

Important Safety Instructions

........................................................................ 11

Product Documentation Online

..................................................................... 12

Software and Firmware License Agreement 

The terms and conditions of this License Agreement (the “Agreement”) will apply to the 
software and/or firmware (individually or collectively the “Software”) incorporated into 
the Paradyne product (the “Product”) purchased by you and any derivatives obtained 
from the Software, including any copy of either. If you have executed a separate written 
agreement covering the Software supplied to you under this purchase, such separate 
written agreement shall govern.

ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS
TERMS, YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED
INTO THE PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU
SHOW YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.

IN THE EVENT THAT YOU DO NOT AGREE WITH ANY OF THE TERMS OF THIS
LICENSE AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT IN ITS
ORIGINAL PACKAGING AND YOUR SALES RECEIPT OR INVOICE TO THE
LOCATION WHERE YOU OBTAINED THE PARADYNE PRODUCT OR THE
LOCATION FROM WHICH IT WAS SHIPPED TO YOU, AS APPLICABLE, AND YOU
WILL RECEIVE A REFUND OR CREDIT FOR THE PARADYNE PRODUCT
PURCHASED BY YOU.

Summary of Contents for SNE2020G-S













Reviews: