background image

Bulletin TI-75A20C 

Installation, Operation and Maintenance Manual

Technical Information 

Parker Balston 75-A20 Compressed Air Dryer

Parker Hannifin Corporation

Industrial Gas Filtration and

Generation Division

Lancaster, NY  •  1-716-686-6400

1

Parker Balston  75-A20 Compressed Air Dryer

Bulletin TI-75A20C

Installation, Operation, and Maintenance Manual

CELL: DRY

®

Introduction

Installation

Balston compressed Air Dryers provide clean, dry air from  

an existing compressed air supply.  The 75-A20 Air Dryer 

delivers  -100°F (-73°C) dewpoint air.

The 75-A20 Compressed Air Dryer is powered by a 12 VDC 

power supply.  Each dryer is equipped with a plug-in trans-

former for connection to the local power supply.

These instructions must be thoroughly read and under-

stood before installing and operating this product.  If you 

have any questions or concerns, please call the Technical 

Services Department at 800-343-4048, 8AM to 5PM Eastern 

Standard Time (North America only) or email at balston-

techsupport@parker.com. For other locations, please 

contact your local representative.

The dryer should be fastened securely, in a vertical position, 

to a wall or similar mounting surface according to National 

Electrical Code (NEC) and local building code guidelines.  All 

mounting hardware supplied by the customer should be ad-

equately sized to support the weight of the unit in its mounted 

position. 

To facilitate routine maintenance, install a shut-off valve on the 

supply air line, upstream from the dryer.  Pipe the supply air 

(60 psig-125 psig, 4.1 barg-8.6 barg) to the inlet port of  

the dryer.  (

Note:

 Pipe size must match inlet and outlet port 

sizes or adequate lengths of pipe must be used to reduce/ 

increase pipe size to match ports.  Please consult factory for 

additional assistance.)  The air dryer should be installed on a 

compressed air system which contains a properly sized  

aftercooler.  The temperature of the supply air entering the 

Balston Air Dryer should not exceed 78°F(25°C).  If the 

temperature of the inlet compressed air exceeds 78°F(25°C), 

the dewpoint of the air generated by the dryer may exceed 

the rated dewpoint.  If the compressed air supply has excess 

water and/or oil or is supplied to the dryer from an elevated air   

 

 

 

 

line, a drip leg must be installed directly upstream from the dryer to reduce the amount of water and oil 

which could get into the dryer and associated valves and cause non-warranty damage to the unit (see Fig-

ure 2).  A minimum supply air pressure to the air dryer of 60 psig (4.1 barg) is required to maintain proper 

operation of the drying towers and associated valves.  The maximum supply pressure should not exceed 

125 psig (8.6 barg) or damage to the unit may occur.

It is important to control output pressure and flow from the dryer to avoid exceeding the rated capacity of 

the dryer.  If the maximum flow rate of the dryer is exceeded, the process air may not meet the published 

dewpoint specifications.  The installation of a pressure regulator and flow control valve downstream from 

the Balston Air Dryer is recommended to control output flow characteristics.

Figure 1 - 75-A20 Compressed Air Dryer

Summary of Contents for 75-A20

Page 1: ...ne upstream from the dryer Pipe the supply air 60 psig 125 psig 4 1 barg 8 6 barg to the inlet port of the dryer Note Pipe size must match inlet and outlet port sizes or adequate lengths of pipe must be used to reduce increase pipe size to match ports Please consult factory for additional assistance The air dryer should be installed on a compressed air system which contains a properly sized afterc...

Page 2: ...Balston Air Dryers requires approximate ly 15 minutes Additional coalescing prefilter cartridges and moisture indicating cartridges for the Balston 75 A20 Air Dryer may be ordered through your local Parker Balston representative Changing filter cartridges more frequently will translate into direct energy savings and reduced operating costs Annual electricity costs to operate a typical 100 HP compr...

Page 3: ...Temperature 2 78 F 25 C Pressure Drop at Max Flow Rate 8 psi 0 5 bar Inlet Outlet Port Size 1 4 NPT Electrical Requirements 3 120 VAC 12 VDC see Note 3 Shipping Weight 80 lbs 36 kg Model Number 75 A20 Replacement Filter Cartridges Filter Cartridges 1st stage box of 10 100 18 DX Filter Cartridges 2nd stage box of 10 100 18 BX Moisture Indicator Filter 1 each 75800 Maintenance Kit 1 Year MK7525 Spec...

Page 4: ...ck electric power source Check flow demand Must match process flow requirements to dryer capacity Check inlet filters for particulate clogging replace if necessary Check for leaks in downstream piping and process Check prefilter drain s for leaks Check supply line pressure 60 psig 4 1 barg minimum Check supply line source compressor Check to make sure all customer installed valves are open Check p...

Reviews: