background image

Contact Information:

Parker Hannifi n Corporation

Refrigerating Specialties Division

2445 South 25th. Avenue 
Broadview, IL 60155-3891

phone (708) 681-6300 
fax (708) 681-6306

www.parker.com

Product Bulletin 22-05 A

Outlet Pressure Regulator

Type: A4WO, A4WOB, A4WOS, A4WOBS, A4WOK,
  

A4WOBK, A4WOE, A4WOES

Size: 20 - 50 mm (

3

4

” to 2”)

Design Pressure Rating: 32 bar (464 psig)

Purpose:

The A4WO outlet pressure 
regulators modulate the fl ow of 
refrigerant gas or liquid to maintain 
a constant downstream pressure.  
This improved design has a higher 
working pressure, greater working 
temperature range than competitive 
products, and minimizes the effects 
of system impurities for a more 
durable operation.  The A4WOs most 
benefi cial features are its stainless 
steel and aluminum construction, 
which allows it to withstand corrosive 
environments and its overall light 
weight minimizes installation costs.

Product Features:

Suitable for Ammonia, CO

• 

2

, R-22, 

R-404a, and other common 
refrigerants
Designed with corrosion resistant 

• 

material – 304 stainless steel and 
aluminum
No body wearing surfaces

• 

Stainless steel components are 

• 

resistant to wiredrawing
Improved performance at low loads 

• 

with a turn down ratio of 10% of 
capacity

Design drastically reduces foreign 

• 

material to fl ow from inlet to 
diaphragm/seat and piston cavity
Light weight

• 

Can be mounted in a horizontal 

• 

and vertical position
Several control options available

• 

Fluid temperature rating: -60

• 

o

C to 

116

o

C (-76

o

F to 240

o

F)

Ambient temperature rating: -40

• 

o

to 60

o

C (-40

o

F to 140

o

F)

Complies with Pressure Equipment 

• 

Directive 97/23/EC

A4WOB

A4WOS

A4WO

A4WOB

A4WOBS

Patent Pending

Summary of Contents for A4WO













Reviews: