background image

USER
MANUAL

MODEL 1070

AC Powered, Synchronous
Short Range Modem

Part #07M1070-C
Doc. #067011U,
Rev. D
Revised 1/22/08

C E R T I F I E D

An ISO-9001

Certified Company

SALES OFFICE
(301) 975-1000
TECHNICAL SUPPORT
(301) 975-1007
http://www.patton.com

Copyright © 1997

Patton Electronics Company

All Rights Reserved

Dear Valued Customer,

Thank you for purchasing Patton Electronics products!   We do

appreciate your business.  I trust that you find this user manual helpful.  

We manufacture one of the widest selections of data

communications products in the world including CSU/DSU's, network
termination units, powered and self-powered short range modems, fiber optic
modems, interface converters, baluns, electronic data switches, data-line surge
protectors, multiplexers, transceivers, hubs, print servers and much more.  We
produce these products at our Gaithersburg, MD, USA, facility, and can
custom manufacture products for your unique needs.

We would like to hear from you.  Please contact us in any of the

following ways to tell us how you like this product and how we can meet your
product needs today and in the future.  

Web:               

http://www.patton.com

Sales E-mail:      

sales@patton.com

Support E-mail:    support@patton.com
Phone - Sales      

(301) 975-1000

Phone - Support  

(301) 975-1007

Fax:                   

(301) 869-9293

Mail:               

Patton Electronics Company
7622 Rickenbacker Drive
Gaithersburg, MD  20879   USA

We are committed to a quality product at a quality price.  Patton

Electronics is ISO 9001 certified.  We meet and exceed the highest standards
in the industry (CE, UL, etc.).

It is our business to serve you.  If you are not  satisfied with any

aspect of this product or the service provided from Patton Electronics or its
distributors, please let us know. 

Thank you.

Burton A.Patton

Vice President

P.S.  Please tell us where you purchased this product.
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________

Summary of Contents for 1070





















Reviews: