background image

 

www.pbteen.com

 

 

 

 

Display-It Desk 

IMPORTANT SAFETY INSTRUCTIONS: 

 

Please read all instructions carefully before assembling. 

 

For your safety, assembly by two adults is recommended. 

 

 

 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
ASSEMBLY INSTRUCTIONS: 
 

1.  Insert the Shelf Support (S) into the pre-drilled holes inside the Door Pedestal (C). Place the Shelf (D) on 

the Shelf Supports (S). 

2.  Pull out the bottom drawer by pressing the clips on both of the metal glides on the sides of the drawers to 

release it from the Drawer Pedestal (B), as shown below. Place the File Grids (K) on the cut-outs of the 
drawer. There are two positions. One is for legal size and the other is for letter size.  
 

              

 
 
 
 
 
 

Hardware Included with 

Hardware Included with 

Two Drawer Pedestal: 

Desk Door Pedestal: 

(F) Allen Key  

 – 1pc 

(N) Allen Key  

 – 1pc 

(G) Bolt ¼” x 25mm 

  – 4pcs  (O) Bolt ¼” x 25mm 

  – 4pcs

(H) Spring Washer  

 – 4pcs 

(P) Spring Washer  

 – 4pcs 

(I) Flat Washer 

 – 4pcs 

(Q) Flat Washer 

 – 4pcs 

(J) Wooden Dowel  

 – 4pcs 

(R) Wooden Dowel  

 – 4pcs

(K) File Grid 

2pcs  (S) Shelf Support  

 

  – 4pcs 

(L) Cable Clip 

 - 1pc 

 

(M) Wood screw  
3.5x15mm  -1pc 
 

 

PARTS INCLUDED: 

 

(A) Desk Top – 1pc 
(B) Drawer Pedestal – 1pc 
(C) Door Pedestal – 1pc 
(D) Shelf – 1pc 
(E) Keyboard Tray – 1pc 

One Door Pedestal 

Two Drawer Pedestal 

Summary of Contents for Display-It Desk

Page 1: ... Pedestal B as shown below Place the File Grids K on the cut outs of the drawer There are two positions One is for legal size and the other is for letter size Hardware Included with Hardware Included with Two Drawer Pedestal Desk Door Pedestal F Allen Key 1pc N Allen Key 1pc G Bolt x 25mm 4pcs O Bolt x 25mm 4pcs H Spring Washer 4pcs P Spring Washer 4pcs I Flat Washer 4pcs Q Flat Washer 4pcs J Wood...

Page 2: ...Flat Washers I Secure the Desk Top A to the Door Pedestal using the Bolts O Spring Washers P and Flat Washers Q Check alignment before fully tightening all bolts 5 Place the drawer back into the Drawer Pedestal B with the cable of the cord set pre installed going through the cut out on back panel Use the Cable Clip L and Wood Screw M to secure the cable in place when required 6 Align and attach th...

Page 3: ... Bracket D over the insert nuts and secure using Bolt E as shown below Tighten with a Phillips Head Screwdriver 3 Insert the Shelf Support Pegs C into the pre drilled holes on the interior sides of the Desk Hutch s center cubby A Place the Shelf B onto the Shelf Support Pegs C Parts Included Hardware Included A Desk Hutch 1pc C Shelf Support Pegs 4pcs B Shelf 1pc D Bracket 4pcs E Bolt 5 32 x 15mm ...

Page 4: ...rniture the second Plastic Wall Bracket G will need to be attached to the furniture frame at the top To do this temporarily move the furniture into its final position and mark the location of the wall s Plastic Wall Bracket G on the furniture frame with a pencil 3 Move the furniture away from the wall and place a Plastic Wall Bracket G on the mark Using the marks from the previous step as a guide ...

Reviews: