WARNING!
READ, UNDERSTAND AND FOLLOW ALL INSTRUCTIONS AND WARNINGS BEFORE
OPERATING THIS TOOL. FAILURE TO DO SO MAY RESULT IN PERSONAL INJURY
AND/OR PROPERTY DAMAGE AND WILL VOID WARRANTY.
7 in. Angle Sander
OWNER’S MANUAL
Stock Number M643
sPecIfIcAtIoNs:
Air pressure (P.S.I.):
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
90
Average air consumption (C.F.M.):
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Free speed (R.P.M.):
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4,500
Spindle Thread:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5/8 - 11
Air inlet (N.P.T.):
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3/8
Hose size (I.D.):
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1/2 in.
Weight (LBS.):
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.19
Specifications are subject to change without notice.
3
IMPORTANT SAFETY INFORMATION
WARNING!
ReAD, uNDeRstAND AND foLLoW ALL INstRuctIoNs AND
WARNINGs BefoRe oPeRAtING tHIs tooL. fAILuRe to Do
so MAY ResuLt IN PeRsoNAL INJuRY AND/oR PRoPeRtY
DAMAGe AND WILL VoID WARRANtY.
1. Use only paper sanding disks with the proper adhesive. Read, under-
stand and follow all adhesive manufacturers’ directions.
Do Not use
cLotH BAcKeD sANDING DIsKs WItH tHIs tooL.
2. Make sure sanding pad RPM rating matches Free Speed rating
of this tool.
3. Wear a dust mask while operating this tool. Read, follow and un-
derstand manufacturers instructions on paint, primer, paint preps,
glazing, body filler, etc. for additional respirator and ventilating
requirements.
4. Always use approved eye and ear protection when using air powered
tools. If raising dust/debris, wear a suitable mask. Do not wear loose
clothing or jewelry.
5. Always operate tool a safe distance from yourself and others in the
work area. Keep footing and balance at all times.
6. Make sure work piece is secure to allow safe operation of the tool with
both hands. Do not hold the work piece in your hand, lap or against
any part of your body.
7. Make sure trigger is in the “off” position before connecting or discon-
necting the tool from air source. Disconnect tool from air source
before changing accessories, performing service and when not in use.
8. Follow air source manufacturer’s directions for connection of regula-
tors, filters and other accessories to air source. Do not install quick
couplers directly at tool air inlet. This causes inlet failure due to
excess weight and vibration. Use a whip hose between tool and quick
couplers.
9. Do Not oVeRLoAD!
Do not force tool. Match tool capacity to work
load requirement. Use tool within its rated capacity and only for its
designated purpose. Overloading air tools will cause premature wear
and/or permanent damage of internal and external drive parts and will
void warranty.
10. Inspect hoses and fittings for wear and damage prior to using tool.
Do not carry or drag tool by the air hose. Keep air hose free from
obstruction, twisting and binding.
