background image

 

  

ETU++ 

 
 

 

 

 

 

Manual 

 
Perun  ETU++  replaces  stock  electronics  in  replicas  with  Electronic  Trigger  Unit  by  G&G.  It 
provides lots of additional features, as well as allows the replica to work with many different 
battery types. 

Reading this manual will help you fully exploit this unit’

s potential and in case 

of encountering any problems, you can look here for solutions. 

 

Manufacturer: 
Perun 
Barwicka 8 St. 
60-

192 Poznań

 

Poland 
e-mail: 

info@perunairsoft.pl

 

 

 

Table of contents 

1. 

Technical data.................................................................................................................................. 2 

2. 

Features and programming ............................................................................................................. 2 

3. 

Factory settings ............................................................................................................................... 4 

4. 

Diagnostic system ............................................................................................................................ 5 

5. 

Switch check .................................................................................................................................... 7 

6. 

Custom/DIY projects ........................................................................................................................ 7 

 

Summary of Contents for ETU++









Reviews: