INSTALL:
4x
INSTALL:
4x
INSTALL:
4x
INSTALL THE ITX MOTHERBOARD WITH 4x MOTHERBOARD SCREWS
Plug in all cables you need for
your build into the power
supply first before installing it
for easier installation
The right-side panel can be
secured with a screw if cables
are pushing against it.
CLEARANCE
REAR
SIDE
FRONT
INSTRUCTION MANUAL
Thank you for choosing Phanteks. Please take a moment to
carefully go through the manual. Phanteks will not take
responsibility for any damages incurred due to incorrect
installation or usage of this product.
This manual supports the following models:
PH-EC200AC_BK
(2x 120 mm Black Fans)
PH-EC200ATG_DBK
(2x 120 mm D-RGB Fans)
INTRODUCTION
PRODUCT OVERVIEW
ECLIPSE P200A
INSTRUCTION MANUAL V1.0
V1.0
English
1. Power Button
2. Reset Button
(P200AC Only)
3. D-RGB Mode
(P200ATG-D Only)
4. D-RGB Color
(P200ATG-D only)
5. Headphone / Microphone
6. USB-C Gen 2
(P200ATG-D only)
7. USB 3.0
Francais
1. Bouton d’alimentation
2. Bouton de réinitialisation
(P200AC Only)
3. D-RGB Mode
(P200ATG-D Only)
4. D-RGB Color
(P200ATG-D Only)
5. Casque / Microphone
6. USB-C Gen 2
(P200ATG-D only)
7. USB 3.0
Deutch
1. Ein-/Aus Schalter
2. Reset-Knopf
(P200AC Only)
3. D-RGB Mode
(P200ATG-D Only)
4. D-RGB Color
(P200ATG-D Only)
5. Kopfhörer / Mikrofon
6. USB-C Gen 2
(P200ATG-D only)
7. USB 3.0
Espanol
1. Botón de encendido
2. Botón de reinicio
(P200AC Only)
3. D-RGB Mode
(P200ATG-D Only)
4. D-RGB Color
(P200ATG-D Only)
5. Auricular / Micrófono
6. USB-C Gen 2
(P200ATG-D only)
7. USB 3.0
ECLIPSE P200A Performance
(PH-EC200AC_BK)
ECLIPSE P200A DIGITAL-RGB
(PH-EC200ATG_DBK)
FRONT I/O FEATURES
STEP 2.
MOTHERBOARD INSTALLATION
THE POWER SUPPLY IS INSTALLED THROUGH THE REAR OF THE CHASSIS. LOOSEN THUMBSCREWS TO REMOVE PSU BRACKET.
INSTALL PSU TO BRACKET WITH 4x PSU SCREWS.
STEP 3.
POWER SUPPLY INSTALLATION
INSTALL THE SSD(s) WITH 4x SSD SCREWS ON THE DEDICATED
SSD BRACKET AND MOUNT IT BACK INTO THE CHASSIS.
STEP 4.
STORAGE INSTALLATION - Dedicated 2.5” SSD Bracket
STEP 1.
REMOVING CHASSIS PANELS
a.
PULL THE SIDE PANEL, THEN LIFT THE PANEL UP
TO REMOVE IT
b.
REMOVE FRONT PANEL
BY PULLING ON THE
PANEL FROM BELOW
c.
REMOVE THE BOTTOM
DUST FILTER FROM
THE FRONT
120
FAN
120
RAD
5
7
6
4
3
1
120
FAN
120
RAD
120
FAN
140
FAN
BOTTOM
120
FAN
120
RAD
140
RAD
CPU Cooler Height
165 mm
GPU Clearance
355 mm
GPU Thickness
3-slot, 65mm
5
7
6*
2
1
LOOSEN:
2x
P200A PRE-INSTALLED ACCESSORIES:
P200A INCLUDED ACCESSORIES:
2x 120 mm Black or
2x 120 mm D-RGB
4x PSU Screw 3x Case Screw 1x Thumb Screw
6x Zip Ties
2x SSD Cover
1x Vertical GPU Mount
21x Motherboard
+ SSD Screw
COLORS
2 SEC
MODES
SOLID
BREATHING
RADAR
SPARKLE
RAINBOW
PRESS AND HOLD THE MODE BUTTON TO TURN OFF LEDS
PRESS AGAIN TO TURN ON
DIGITAL-RGB CONTROLS (P200ATG_D MODEL)
1
2
1
2
*Optional upgrade