background image

Service Manual

Philips Consumer Lifestyle

Published by Philips Consumer Lifestyle 

Printed in the Netherlands 

© Copyright reserved 

Subject to modification

 Steam 

Generator

GC9220

11/08

PRODUCT INFORMATION

Fast & powerful crease removal

- Soleplate: SteamGlide
- OptimalTemp
-  Continiuous steam output: 120 g/min
-  Steam boost: 230 g/min
- Vertical steam
-  Steam pressure: Up to 5 bar
- Steam tip
- Power: 2400 W

Easy to use

-  Water tank capacity: 1500 ml
-  Filling and emptying water: Detachable water tank

Extra large opening door

-  Refill any time
-  Heat-up time: 2 min
-  Hose storage: Hose storage compartment
-  Cord storage: Cord storage compartment
-  Power cord lenght: 1.8 m
-  Cord freedom (swivel): 180 degree cord freedom
-  Hose length: 1.7 m
-  Safe for all fabrics: Even for delicates like silks

Calc management

-  Suitable for tap water
-  Calc clean solution: Easy De-calc
-  Calc clean reminder

EMF & Service Information

-  This product meets the requirements regarding interference 

suppression on radio & TV.

-  After the product has been repaired, it should function 

properly & has to meet the safety requirements as officially 
laid down at this moment.

TECHNICAL INFORMATION

Voltage   

:  220 - 240 V

Frequency 

:  50 - 60 Hz

Power  - Iron 

:  800 W  at 230 V

   

- Boiler 

:  1370 W  at 230 V

Dimension (F-box)  :  491 mm x 305 mm x 335 mm

 

 

  (Depth x Width x Height)

Weight   

:  Weight of iron: 1.2 kg

 

 

  Weight of iron + base: 5 kg

Optimal Temp technology

-  Delivers always perfect combination of steam and temperature
-  100% easy to use, no adjustment required
-  100% safe on all ironable garments
-  100% effective on all fabrics, no other iron is faster
-  Tested and approved by independent textile experts

 

 

  Always the perfect setting thanks to:

 

 

  1 - Cylonic steam chamber

 

 

  2 - Advanced Smart control processor

Easy De-calc

Easy De-calc cap allows hassle free & effective scale removal
to extend the life of the steam generator.

1

2

Summary of Contents for GC9220













Reviews: