3-Way or More Applications (Multi-Location)
OccuSwitch Manual-ON Occupancy Sensor Remote
California Title 24 2008 Compliant
Cat. No. LRS2211R - 120VAC, 60Hz
For use with Cat. No. LRS22110 Sensors
INSTALLATION INSTRUCTIONS
WARNINGS AND CAUTIONS:
•
TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT THE POWER IS OFF BEFORE WIRING!
•
To be installed and/or used in accordance with electrical codes and regulations.
•
To avoid overheating and possible damage to this device and other equipment,
DO NOT install to control a receptacle.
•
Use only one LRS22110 sensor in a multi-location circuit with up to LRS2211R matching remotes with LEDs.
WARNINGS AND CAUTIONS:
•
If you are not sure about any part of these instructions, consult an electrician.
•
The Manual-On Occupancy Sensor Remote is intended to replace additional 3-Way and 4-Way switches when used with the LRS22110
Occupancy Sensors.
•
Do not touch the surface of the lens. Clean outer surface gently with damp cloth only.
DO NOT use soaps or cleaning liquids.
• Use this device
WITH COPPER OR COPPER CLAD WIRE ONLY.
DI-401-IPV0R-02A
4-Way Wiring of Sensor Remote with LRS22110
Sensor:
Step 4b
TOOLS NEEDED TO INSTALL YOUR DEVICE
INSTALLING YOUR REMOTE
NOTE: Use check boxes when Steps are completed.
√
Slotted/Phillips Screwdriver
Electrical Tape
Pliers
Pencil
Cutters
Ruler
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
Step 1
WARNING:
TO AVOID FIRE, SHOCK, OR DEATH;
TURN OFF POWER at circuit breaker or fuse and test
that power is off before wiring!
Step 2
Identifying your wiring application
(most common) -
NOTE: If the wiring in the wall box
does not resemble any of these configurations, consult an
electrician.
3
5
1
2
6
4
4-Way
1. First Traveler – note color
2. Second Traveler – tagged
3. Neutral
4. Ground
5. Third Traveler – note color
6. Fourth Traveler – tagged
NOTE: For matching remote
w/LEDs installation, the
First
Traveler becomes Line Hot.
2
4
1
5
3
3-Way
1. Line or Load (See important
instruction below)
2. Neutral
3. Ground
4. First Traveler – note color
5. Second Traveler – note color
NOTE: For matching remote
w/LEDs installation, the
First
Traveler becomes Line Hot.
3-Way Wiring of Sensor Remote with
LRS22110 Sensor:
Step 4a
IMPORTANT:
For 3-Way applications, note that one of the screw terminals from
the old switch being removed will usually be a different color (Black) or
labeled Common. Tag that wire with electrical tape and identify as the
common (Line or Load) in both the sensor wall box and remote wall box.
For 4-Way applications, note that the old switch being removed will
have 4 screws plus a ground screw. Tag the two same color insulated
wires with electrical tape.
BK
RD
3-Way
WH
BK
RD
3-Way
WH
Terminal
Screw marked
White (WH)
Terminal
Screw marked
White (WH)
Terminal
Screw marked
Red (RD)
3
1
3
2
4
LRS22110 Sensor
LRS2211R Remote
Additional
Neutral Wire
Terminal
Screw
marked
3-Way
Terminal
Screw
marked
Black (BK)
Ground
Terminal
Screw
(Green)
Terminal
Screw
marked
3-Way
Terminal
Screw
marked
Black (BK)
Ground
Terminal
Screw
(Green)
5
1
5
Hot (Black)
Neutral (White)
LRS22110 Sensor
LRS2211R Remote
3-Way
RD
WH
BK
3-Way
WH
BK
Black
White
Line
120VAC, 60Hz
Green
Ground
Green
Ground
LOAD
NOTE: The Occupancy Sensor must be installed in a wall box that has a Load
connection. The sensor remote
must be installed in a wall box with a Line Hot
connection and a Neutral connection. A Neutral wire to the sensor remote needs
to be added as shown. If you are unsure about any part of these instructions,
consult an electrician.
NOTE: Maximum wire length from sensor to all installed
remotes cannot exceed 300 ft (90 m).
WIRING SENSOR REMOTE (3-Way wall box with Line Hot
connection):
Connect wires per WIRING DIAGRAM as follows:
NOTE: Use backwire connection when connecting two wires to one screw terminal.
• Green or bare copper wire in wall box to Green terminal screw on Sensor
Remote.
• Line Hot (common) wall box wire identified (tagged) when removing old
switch and First Traveler wall box wire to Sensor Remote terminal screws
marked "BK".
• Second Traveler wall box wire from other 3-Way wall box to Sensor Remote
terminal screw marked "3-Way". This traveler from the remotes must go to the
terminal screw marked "3-Way" on the sensor.
• Neutral wall box wire to remote terminal screw marked "WH".
WIRING SENSOR (3-Way wall box with Load connection):
Connect wires per WIRING DIAGRAM as follows:
NOTE: Use backwire connection when connecting two wires to one screw terminal.
• Green or bare copper wire in wall box to Green terminal screw on sensor.
• Load wall box wire identified (tagged) when removing old switch to terminal
screw marked "RD" on sensor.
• First Traveler Line Hot to terminal screw marked "BK" on sensor.
• Remove Red insulating label from terminal screw marked "3-Way" on sensor.
• Second Traveler wall box wire
(note color as above) to terminal screw
marked "3-Way" on sensor. This traveler must go to the terminal screw on
the Sensor Remote marked "3-Way" or to the terminal screw on the Vizia
matching switch remote marked "YL/RD".
• Neutral wall box wire to terminal screw marked "WH" on sensor.
BK
RD
3-Way
WH
BK
RD
3-Way
WH
LRS2211R Remote
(3-Way Wall box from Step 2)
LRS2211R Remote
(4-Way Box from Step 2)
LRS22110 Sensor
(3-Way Wall Box from Step 2)
Terminal
Screw marked
White (WH)
Terminal
Screw marked
White (WH)
3
2
4
Terminal
Screw marked
White (WH)
3
1
Additional
Neutral Wire
Additional
Neutral Wire
BK
YL/RD
WH
RD
3
6
2
1
Terminal
Screw
marked
Yellow/Red
(YL/RD)
Terminal
Screw
marked
Black (BK)
5
5
Terminal
Screw marked
Red (RD)
1
5
4
Terminal
Screw
marked
3-Way
Terminal
Screw
marked
Black (BK)
Ground
Terminal
Screw
(Green)
Terminal
Screw
marked
3-Way
Terminal
Screw
marked
Black (BK)
Ground
Terminal
Screw
(Green)
Ground
Terminal
Screw
(Green)
4
2
Hot (Black)
Neutral (White)
LRS22110 Sensor
LRS2211R Remote
VP0SR-1L Remote
YL/RD
3-Way
RD
WH
WH
BK
3-Way
WH
BK
BK
Line
120VAC, 60Hz
Black
White
Green
Ground
Green
Ground
LOAD
Green
Ground
NOTE: The Occupancy Sensor must be installed in a wall box that has a Load
connection. The sensor remote
must be installed in a wall box with a Line Hot
connection and a Neutral connection. A Neutral wire to the sensor remote needs to
be added as shown. If you are unsure about any part of these instructions, consult
an electrician.
NOTE: Maximum wire length from sensor to all installed remotes
cannot exceed 300 ft (90 m).
WIRING SENSOR REMOTE (3-Way wall box with Line Hot
connection):
Connect wires per WIRING DIAGRAM as follows:
NOTE: Use backwire connection when connecting two wires to one screw terminal.
• Green or bare copper wire in wall box to Green terminal screw on Sensor
Remote.
• Line Hot (common) wall box wire identified (tagged) when removing old switch
and First Traveler wall box wire to Sensor Remote terminal screw marked "BK".
• Second Traveler wall box wire from 4-way wall box to Sensor Remote terminal
screw marked "3-Way"
(note wire colors). This traveler from the remotes must
go to the terminal screw marked "3-Way" on the sensor.
• Neutral wall box wire to remote terminal screw marked "WH".
WIRING SENSOR REMOTE (4-Way wall box):
Connect wires per WIRING DIAGRAM as follows:
NOTE: Use backwire connection when connecting two wires to one screw terminal.
• Green or bare copper wire in wall box to Green terminal screw on Sensor
Remote.
• First Traveler and Third Traveler wall box wires to Sensor Remote terminal screw
marked "BK".
• Second Traveler (tagged) and Fourth Traveler (tagged) wall box wires to Sensor
Remote terminal screw marked "3-Way" terminal screw marked "YL/RD"
(note
wire colors). This traveler from the remotes must go to the terminal screw
marked "3-Way" on the sensor.
• Neutral wall box wire to remote terminal screw marked "WH".
WIRING SENSOR (3-Way wall box with Load connection):
Connect wires per WIRING DIAGRAM as follows:
NOTE: Use backwire connection when connecting two wires to one screw terminal.
• Green or bare copper wire in wall box to Green terminal screw on sensor.
• Load wall box wire identified (tagged) when removing old switch to terminal
screw marked "RD" on sensor.
• First Traveler Line Hot to terminal screw marked "BK" on sensor.
• Remove Red insulating label from terminal screw marked "3-Way" on sensor.
• Second Traveler wall box wire
(note color as above) to terminal screw marked
"3-Way" on sensor. This traveler must go to the terminal screw on the Sensor
Remote marked "3-Way".
• Neutral wall box wire to terminal screw marked "WH" on sensor.
CHANGING THE COLOR OF YOUR DEVICE
Your device may include color options. To change color of the face
proceed as follows:
RESET
RESET
TESTTEST
1 2
0 3
Push down
tabs per
diagram,
one at a time
and rotate
forward to
release
Attach new
face by
inserting
bottom hinge
tabs, then
pivot and
snap the
color kit to
attach
•
Make sure that the ends of the wires from the wall box are
straight (cut if necessary).
• Remove insulation from each wire in the wall box as shown.
Strip Gage
(measure bare wire
here or use gage on
back of the remote)
5/8”
(1.6 cm)
Cut
(if necessary)
Step 3
Preparing and connecting wires:
This remote can be wired using side wire terminal
screws or through backwire openings. Choose
appropriate wire stripping specifications accordingly.
Side Wire
Side wire terminals
accept #14-12 AWG
solid copper wire only.
Back Wire
Back wire openings
use #14-12 AWG
solid
copper wire only.
BK
RD
YL 3-Way
WEB
VERSION
