background image

 

Philips Lighting North America Corporation 
200 Franklin Square Drive 
Somerset, NJ  08873, USA 
Phone:  855-486-2216 

www.philips.com/luminaires

  

Philips Lighting Canada Ltd. 
281 Hillmount Road, 
Markham, ON, Canada  L6C 2S3 
Phone:  800-668-9008 

www.philips.com/luminaires

 

9140052682  February 2016 

 

 

 

SV16 Series 

 

6V 11W 

 

120/277V 60Hz Emergency Luminaire 

Damp Location Standard 

Wet Loc. / Battery Heater Optional 

 

 

 
 
 
 
 
 
 
 
   

 
 

 
 
 
 

INSTALLATION AND 

OPERATING 

INSTRUCTIONS 

 

IMPORTANT 

SAFEGUARDS 

 
When  using  electrical  equipment,  basic  safety 
precautions  should  always  be  followed,  including 
the following: 

 

READ AND FOLLOW ALL 

SAFETY INSTRUCTIONS 

 

All  servicing  should  be  performed  by  qualified 
personnel only. 
 
Equipment  should  be  mounted  in  locations  and  at 
heights  where  it  will  not  be  readily  subjected  to 
tampering by unauthorized personnel. 
 
The  use  of  accessory  equipment  not  recommended 
by the manufacturer may cause an unsafe condition. 
 
Do  not  use  this  equipment  for  other  than  intended 
use. 
 

Do not let power supply cords touch hot surfaces. 
 
Do not mount near gas or electric heaters. 
 

CAUTION:    Halogen  cycle  lamp(s)  are  used  in 
this  equipment.    To  avoid  shattering:    Do  not 
operate  lamp  in  excess  of  rated  voltage,  protect 
lamp against abrasion and scratches and against 
liquids  when  lamp  is  operating,  dispose  of  lamp 
with care. 

 
Halogen  cycle  lamps  operate  at  high  temperatures.  
Do  not  store  or  place  flammable  materials  near 
lamp. 
 
 
CAUTION:    “To  avoid  electrical  overload,  total 
connected  lamp  load  (factory  and  field  installed) 
should not exceed output rating”. 
 
Do not use this equipment for other than intended 
use. 

SAVE THESE 

INSTRUCTIONS 

 

WARNING – Shut off AC power to branch circuits 
to which units will be connected.  All wiring should 
be  per  National  Electrical  Code  and  local 
regulations.

 

Summary of Contents for SV16 Series

Page 1: ...pering by unauthorized personnel The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition Do not use this equipment for other than intended use Do not let power supply cords touch hot surfaces Do not mount near gas or electric heaters CAUTION Halogen cycle lamp s are used in this equipment To avoid shattering Do not operate lamp in excess of rated voltage pr...

Page 2: ...ten backplate to junction box using two 8 32x1 1 4 screws supplied For wet location units ensure that the gasket is evenly compressed around perimeter For installation using surface conduit damp location units only Remove necessary mounting knockouts and secure conduit to flange provided at top of backplate Mount backplate to wall using mounting hardware supplied by others Connect AC Harness found...

Page 3: ...g inside electronics module Connect battery harness to charger board Install electronics module to backplate by hinging together at top and snapping together at bottom Two 6x1 2 screws are provided for further securing electronics module to backplate if so desired Install lamps provided by snapping into ceramic lamp holders on lamp head Attach cover by snapping over electronics module Cover will l...

Page 4: ...attery leads prior to energizing AC power will not turn on the emergency lamps After AC power is energized the emergency lamps will turn on upon AC power failure B This equipment is provided with a low battery disconnect feature which prevents full discharge of battery If the building is to be unoccupied for an extended period and AC is shut off the battery should be disconnected from the charger ...

Reviews: