background image

Note:
• This unit is for vehicles with a 12-volt battery and

negative grounding. Before installing it in a 
recreational vehicle, truck or bus, check the battery
voltage.

• To avoid shorts in the electrical system, be sure to

disconnect the 

battery cable before beginning

installation.

• Refer to the owner’s manual for details on 

connecting the power amp and other units, then
make connections correctly.

• Secure the wiring with cable clamps or adhesive

tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.

• Route and secure all wiring so it cannot touch any

moving parts, such as the gear shift, handbrake and
seat rails. Do not route wiring in places that get
hot, such as near the heater outlet. If the insulation
of the wiring melts or gets torn, there is a danger of
the wiring short-circuiting to the vehicle body.

• Don’t pass the yellow lead through a hole into the

engine compartment to connect to the battery. This
will damage the lead insulation and cause a very
dangerous short.

• Do not shorten any leads. If you do, the protection

circuit may fail to work when it should.

• Never feed power to other equipment by cutting

the insulation of the power supply lead of the unit
and tapping into the lead. The current capacity of
the lead will be exceeded, causing overheating.

• When replacing fuse, be sure to use only fuse of

the rating prescribed on this unit.

• Since a unique BPTL circuit is employed, never

wire so the speaker leads are directly grounded or
the left and right 

speaker leads are common.

• The black lead is ground. Please ground this lead

separately from the ground of high-current 
products such as power amps.
If you ground the products together and the ground
becomes detached, there is a risk of damage to the
products or fire.

• Speakers connected to this unit must be high-

power types with minimum rating of 45 W and
impedance of 4 to 8 ohms. Connecting speakers
with output and/or impedance values other than
those noted here may result in the speakers catch-
ing fire, emitting smoke, or becoming damaged.

• If the RCA pin jack on the unit will not be used, do

not remove the caps attached to the end of the con-
nector.

• When this product’s source is switched ON, a 

control signal is output through the blue/white
lead. Connect to an external power amp’s system
remote control or the car’s Auto-antenna relay
control terminal. (Max. 300 mA 12 V DC.) If the
car features a glass antenna, connect to the antenna
booster power supply terminal.

• When an external power amp is being used with

this system, be sure not to connect the blue/white
lead to the amp’s power terminal. Likewise, do not
connect the blue/white lead to the power terminal
of the auto-antenna. Such connection could cause
excessive current drain and malfunction.

• To avoid short-circuiting, cover the disconnected

lead with insulating tape. Especially, insulate the
unused speaker leads without fail. There is a 
possibility of short-circuiting if the leads are not
insulated.

• To prevent incorrect connection, the input side of

the IP-BUS connector is blue, and the output side
is black. Connect the connectors of the same colors
correctly.

• If this unit is installed in a vehicle that does not

have an ACC (accessory) position on the ignition
switch, the red lead of the unit should be connected
to a terminal coupled with ignition switch ON/OFF
operations. If this is not done, the vehicle battery
may be drained when you are away from the 
vehicle for several hours. (Fig. 1)

Fig. 1

• Cords for this product and those for other 

products may be different colors even if they
have the same function. When connecting this
product to another product, refer to the supplied
Installation manuals of both products and 
connect cords that have the same function.

No ACC position

ACC position

ON

S

T

A

R

T

O

FF

ACC

ON

S

T

A

R

T

O

FF

INST

ALLA

TION MANUAL

MANUEL D’INST

ALLA

TION

<99G00F0V01>

DEH-P4100

Printed in Thailand

Imprimé en Thaïlande

<CRD3064-A/N> UC

+

+

+

+

+

+

+

+

This Product

Multi-CD player
(sold separately)

IP-BUS cable

IP-BUS input (Blue)

Antenna jack

Blue/white
To system control terminal of the power amp
or Auto-antenna relay control terminal.
(Max. 300 mA 12 V DC.)

Fuse

Connecting cords
with RCA pin plugs
(sold separately)

Fuse resistor

System remote control

Fuse holder

Power amp
(sold separately)

Rear output

Front output

Rear speaker

Rear speaker

Right

Front speaker

Rear speaker

White

Gray

White/black

Green

Green/black

Gray/black

Violet

Violet/black

Front speaker

Rear speaker

Left

Front speaker

Front speaker

Perform these connections when using a
different amp (sold separately).

With a 2 speaker system, do not connect
anything to the speaker leads that are not
connected to speakers.

Yellow
To terminal always supplied
with power regardless of
ignition switch position.

Black (ground)
To vehicle (metal) body.

Red
To electric terminal controlled
by ignition switch (12 V DC)
ON/OFF.

White/yellow

Brown

See the section “DFS Alarm
Installation”.

Power amp
(sold separately)

Fuse resistor

Fig. 2

<ENGLISH>

Connecting the Units

Fig. 2

This product conforms to CEMA cord colors.
Le code de couleur des câbles utilisé pour ce produit est
conforme à CEMA.

Summary of Contents for Super Tuner IIID DEH-P4100







Reviews: