USER GUIDE
INSTRUC
TIONS
CA
UTION:
This i
s a high speed t
ool. Negligen
ce m
ay c
aus
e injury if
not h
andled pr
operly.
This t
ool is n
ot a toy an
d is n
ot inten
ded for us
e by
children 14 y
ear
s or youn
ger without a
dult supervi
sion.
Do not a
llow t
ool to c
ome in c
ontact with an
y liquid or
immer
se in w
ater a
s it may c
aus
e dam
age
.
To a
void o
verh
eatin
g, do n
ot operat
e continuo
usly f
or
mor
e than 2 minut
es at a time.
Keep h
air, los
e clothing, je
welry a
way fr
om tool ti
p as it
may bec
ome entan
gled and c
aus
e injury
.
Use e
ye pr
otection an
d a dust mas
k while s
andin
g,
engr
avin
g or grindin
g.
Do not in
sert an
y objects into th
e tool oth
er than th
e tool
bits included.
After c
ompletin
g use of t
ool, turn to off position an
d keep
out of r
each of childr
en.
WARNING: CHOKING HAZARD
– Sm
all p
arts. Not f
or
children un
der 14 year
s or youn
ger witho
ut adult
superv
ision.
Maximum oper
ating s
peed is 15,000 rpm.
©2019 PLAID ENTERPRISES, INC. • 09/19
P.O. BOX 7600 • NORCROSS, GA 30091-7600
(800)842-4197 • MADE IN CHINA
34670E
1. R
otate th
e batt
ery cov
er at the en
d of tool t
o open.
2. In
sert tw
o 1.5V AA batt
eries into t
ool being s
ure t
o follo
w
the pl
acem
ent guide s
hown on t
ool.
3. R
otate th
e end b
attery c
over t
o the “I” m
ark to en
sur
e the
tool i
s in “On” m
ode.
4. To in
sert ti
p, fir
st press S
haft L
ock Butt
on and r
otate th
e
collet nut b
y han
d until the lock en
gages th
e shaft,
prev
enting r
otation, then in
sert desir
ed tip. While h
old-
ing th
e Shaft L
ock Butt
on, rev
erse r
otate th
e collet nut
into s
ecur
e position.
5. Pr
ess the w
ork butt
on to start usin
g tool. R
eleas
e the
work b
utton t
o stop t
ool.
6. Wh
en chan
ging t
ool tips a
lw
ays r
otate th
e end b
attery
cov
er to th
e left to just p
ast th
e “0” mark t
o ensur
e tool i
s
in OFF mode
.
7. Aft
er use, r
emov
e the b
attery c
over an
d rem
ove b
atteries
befor
e storin
g aw
ay, o
ut of rea
ch of children.
SAFE
TY PRE
CA
UTIONS
MAINTENANCE
1. For best results use alkaline batteries. Do not mix old and
new batteries.
2. Do not mix alkaline, standard or rechargeable batteries.
3. Do not use tool continuously for more than 2 minutes at a
time as longer use may result in overheating tool motor
and shorten tool’s lifespan.
4. Tool can operate for approx. 30 cycles (2-minute continuous
use with 1 min break) using new batteries.
5. When tool is not in use, remove batteries and store away
from small children.
ENGRAVER
Summary of Contents for ENGRAVER
Page 1: ...USER GUIDE ENGRAVER...
Page 5: ...TIPS INCLUDED...
