background image

The above steps introduce the simple installations and configurations of 

the device. For further configurations, please refer to the user manual, 

which can be downloaded from the website.

WBS-202N/WBS-502N: 

http://www.planet.com.tw/en/support/downloads?metho

d=category&c1=wireless-lan&p=&type=3

PLANET Management Hardware WLAN Controller 

(WAPC-500/WAPC-1000): 

http://www.planet.com.tw/en/support/downloads?metho

d=category&c1=wireless-lan&p=&type=3

PLANET Management Software WLAN Controller 

(Smart AP Control): 

http://www.planet.com.tw/storage/products/48976/Smar

t%20AP%20Control%20-%20Configuration%20Guide_v1

.0.pdf

If you have further questions, please contact the local dealer or 

distributor where you purchased this product.

PLANET Technology Corp.

10F., No 96, Minquan Rd., Xindian Dist., 

New Taipei City 231, Taiwan

1. Package Contents

2. Physical Introduction

– 1 –

– 2 –

– 3 –

– 4 –

3. Hardware Installation

Hardware Description

2011-E10730-000

Step 1:

 Push the latch on the bottom of the Outdoor Wireless CPE to 

remove the sliding cover.

Note

If there is any item missing or damaged, please contact the 

seller immediately.

– 5 –

– 6 –

– 7 –

– 8 –

4.  Wired Network Configuration

  (Windows 7 and Windows 10)

A computer with wired Ethernet connection is required for the first-time 

configuration of the Wireless AP.

1. Click the 

“Start”

 button located at the lower-left corner of your 

computer.

2. Select 

“Control Panel-> Network and Sharing Center”

.

3. Click 

“Change adapter settings”

.

4. Double-click 

“Local Area Connection”

.

5. Select 

“Internet Protocol Version 4 (TCP/IPv4)”

 and click 

“Properties”

.

6. Select 

“Use the following IP address”

 to configure the IP address 

to 

“192.168.1.x”

 ("x" can be any number from 2 to 254, except 

253) and then click the 

“OK”

 button to save the configuration.

Further Information

Step 1: 

Launch the Web browser and enter the default IP address 

http://192.168.1.253

Step 2:

 The default password is 

“admin”

. Then click the 

LOGIN

 

button to continue.

For security reasons, it is recommended to change the password at the 

first login and memorize it..

Default IP Address: 

192.168.1.253

Default Password: 

admin

Default SSID: 

PLANET _2.4G

 or 

PLANET _5G

Quick Guide

IMPORTANT SAFETY PRECAUTIONS:

1) 

LIVES MAY BE AT RISK!  

Please be aware of the 

electrical wires around. Carefully read the section

 

"OUTDOOR INSTALLATION WARNING" 

in the manual 

before installation.

2) Users 

MUST

 complete grounding wired with the device; 

otherwise, a sudden lightning could cause fatal damage to 

the device. 

EMD (Lightning) DAMAGE IS NOT 

COVERED UNDER WARRANTY

WBS-202N/WBS-502N

Ethernet Cable x 1

Mounting Strap x 1

Thank you for choosing PLANET Outdoor Wireless CPE. Before installing, 

please verify the contents inside the package box. The device mentioned 

herein is the brief name of the "Outdoor Wireless CPE".

Reset/Pair

PoE

LAN

WDS Switch

DC Power

 

WBS-202N/WBS-502N

802.11n 300Mbps 

Outdoor Wireless CPE

Step 2:

 Plug the RJ45 Ethernet cable into the PoE Port of the Outdoor 

Wireless CPE. Then, slide back the cover to finish the 

installation.

Step 3:

 Place the mounting strap through the slot on the back of the 

Outdoor Wireless CPE and then around the pole. Tighten the 

mounting strap to secure the Outdoor Wireless CPE.

To PoE Switch

Step 2:

 Go to the “Search” page to discover and add the managed AP 

to the device list. Then, you can go to the “Control-> AP 

Management” page to configure pre-defined profiles to the 

managed AP without logging on to the AP’s web page.

For information about further configuration of Managed AP by using 

PLANET Smart AP Control, refer to the configuration guide of the SAPC.

Step 1:

 Launch the Web browser (Google Chrome is recommended) 

and enter the default IP address https://192.168.1.100:8888 

of the SAPC. Then, enter the default username and password 

“admin” to log on to the system. 

 

* The secure login with SSL (HTTPS) prefix is required.

5. Entering into the Web Management

6. Easy to Set Up PtP WDS Connection

Step 3:

 For security reasons, it is strongly recommended 

to go to 

Advanced

 to configure the Encryption Method and Passphrase 

of your wireless network.

7. AP Discovery through 

  PLANET Smart AP Control (SAPC)

Step 1: 

(1) Position “S” to “M” on the master AP. Stay in “S” on the 

slave AP.

 

(2) Press the “Reset/Pair” button within 2 minutes on both 

sides.

 

(3) The connection will be established easily.

The WBS-202N and the WBS-502N are the Smart AP series which can 

be centrally managed by PLANET WLAN Controller.
Follow the steps below to discover the managed AP through PLANET 

Smart AP Control (SAPC). Please ensure each managed AP uses a 

different static IP in the same subnet before physically connecting to 

the managed network.
*** Please regularly check PLANET website for the latest compatible list 

of the controller/managed APs in each firmware version.

3-Step to Set Up PtP WDS

S

M

WDS

S

M

WDS

S

M

WDS

Connected

Connecting

Press 

Reset

 within 2 mins

Position “

S

” to “

M

” on master AP  

Step 1

Step 2

Step 3

S

M

WDS

Reviews: