background image

CORDLESS HEADSET SOLUTION WITH BLUETOOTH™ 

M1500

QUICK START AND INFORMATION GUIDE

!

!

!

!

S A F E T Y  

Check local laws regarding use of a mobile
phone and headset while driving.
If you use the product while driving ensure your
attention and focus remains on your responsibility
of driving safely.
CHILDREN. Never allow children to play with 
the headset/adapter — small parts may be a
choking hazard.
Batteries can be swallowed by children and 
are dangerous if swallowed. Always store 
and dispose of batteries where children can’t
reach them.
Observe all signs that require an electrical device
or RF radio product to be switched off in desig-
nated areas. These could include hospitals, blast-
ing areas, and potentially explosive atmospheres.
Turn off your headset/adapter prior to boarding
an aircraft. Do not use your headset in an aircraft.
Never mount or store your headset/adapter over
any air bag deployment area as serious injury
may result when an air bag deploys.

B AT T E R I E S

CAUTION: To reduce the risk of fire or injury

to persons, read and follow these instructions.

1. Use only the batteries supplied with this product;

Plantronics Part Number 35923-01. 

2. Do not dispose of batteries in a fire. The cells

may explode. Check with local codes for 
possible disposal instructions.

3. Do not open or mutilate batteries. Released elec-

trolyte is corrosive and may cause damage 
to eyes or skin and may be toxic if swallowed.

4. Exercise care in handling the batteries in order 

not to “short” the battery contacts with conducting
materials such as rings, bracelets, or keys. 
The batteries or conductor may overheat and 
cause burns.

5. Observe proper orientation between batteries

and charger contacts.

C H A R G I N G

CAUTION: Use only the supplied Class 2

AC adapter to charge the headset/adapter from
an AC voltage or wall outlet.

CAUTION: If the headset/adapter becomes

hot during charging, disconnect AC adapter from
the wall and contact qualified service personnel.

CAUTION: Do not disassemble the AC

adapter of this product as it may expose you to
dangerous voltages or other risks. Incorrect
reassembly can cause electric shock when the
product is subsequently used.

CAUTION: Do not use the charger outdoors

or in damp areas.
Only charge the batteries in accordance with the
instructions of this manual.
Charger Output: 5.5V/500mA maximum, center
contact positive.

C A R E

Never submerge your headset/adapter in water
or other liquids.
Protect your headset/adapter from spills, 
excessive rain, and wet locations.
Do not use liquid cleaners or aerosol cleaners as
they may damage the headset/adapter.
Use a damp cloth to clean the external portions
of the headset/adapter.
Do not stick anything inside the product as this
may damage internal components.

PARTS AND ACCESSORIES

IMPORTANT SAFETY INSTRUCTIONS

OTHER IMPORTANT INSTRUCTIONS

ABOUT

PLANTRONICS

CORDLESS HEADSET SOLUTION WITH 

BLUETOOTH™

Your Plantronics 

M1500

cordless headset solution utilizes

2.4GH

z Bluetooth technology to provide lightweight, hands-free

and wire-free communication for your headset-ready mobile

phone. Designed for maximum comfort and ease of use, this

cordless headset solution is tailored to suit your mobile lifestyle.

This guide will help you set up and use your cordless headset.

Your headset is compliant with version 

1. 1

of the Bluetooth Spec-

ification and supports the Headset Profile. The adapter unit 

also supports the Headset Profile as an Audio Gateway device. 

For accessibility information call the Plantronics T

echnical

Assistance Center 

(TAC)

at 

(800) 544-4660

or visit

www.plantronics.com.

M 1 5 0 0   B AT T E RY

Replacement battery for headset or adapter,
2.4V

Nickel Metal Hydride (NiMH).

M 1 5 0 0   F L E X I B L E   E A R L O O P

Replacement headset earloop.

A C   A D A P T E R

110

-Volt AC Adapter. Replacement AC

adapter/charger for North America.
230-

Volt AC Adapter. Replacement AC

adapter/charger for Europe.
230-

Volt UK AC adapter. Replacement AC

adapter/charger for United Kingdom.

C A R   L I G H T E R   A D A P T E R

Optional car lighter adapter allows you to
charge your M1500 headset and adapter
from any 12-Volt car lighter socket.

NOTE

— Do not use your M15000 headset

while charging if both the adapter and 
your phone are also charging. Poor audio
will result.

M 1 5 0 0   H E A D S E T

Replacement headset for your M1500
system. Battery included.

A 5 0 0   A D A P T E R

Replacement adapter for your M1500
system. Battery included.

PAIRING TO ANOTHER DEVICE

FIG. 7.1A

FIG. 7.1B

FIG. 7.2

FIG. 7.3

WARRANTY AND SERVICES

IN THE UNITED STATES

IN CANADA

Plantronics Service Center 

Plantronics Service Center

345 Encinal Street 

1455 Pitfield Boulevard

Santa Cruz, 

Saint-Laurent,

CA 95060 

Quebec H4S lG3

Tel:

800.544.4660 Tel:

800.540.8363

(toll free) 

(toll free)

514.956.8363
(toll call)

Fax: 800.279.0162 

Fax: 514.956.1825

(toll free) 

(toll call)

Please use the original container, or pack the unit(s) in a car ton
with sufficient packing material to prevent damage. Include the
following information:

1. Proof of purchase indicating model number and date of

purchase.

2. Bill-to address.

3. Ship-to address.

4. Number and description of units shipped.

5. Name and telephone number of person to call, should con-

tact be necessary.

6. Reason for return and description of the problem.

The following one-year warranty and service information
applies only to product purchased and used in the U.S. and
Canada. Contact your local retail dealer for warranty informa-
tion in your country. During this warranty time, if the product is
defective in workmanship or materials, Plantronics, at our
option, will replace or exchange it for a model of equal value.
Damage caused by improper care, accidents, unauthorized
repair or modifications are not covered under this warranty.

NEITHER PLANTRONICS NOR YOUR RETAIL DEALER OR
SELLING DISTRIBUTOR HAS ANY RESPONSIBILITY FOR
ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES,
INCLUDING WITHOUT LIMITATION, DAMAGE TO PROP-
ERTY, COMMERCIAL LOSS OF PROFIT, OR FOR ANY
EXPENSES, LOSS OF TIME, OR INCONVENIENCE.
SOME STATES DO NOT ALLOW EXCLUSION OR LIMITA-
TION OF INCIDENTAL OR CONSEQUENTIAL DAMAGE,
SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT
APPLY TO YOU.

To obtain warranty service, please prepay shipment and return
the unit to the appropriate facility listed at right:

Consult the dealer or an experienced radio/TV technician
for help.

NOTE: Modifications not expressly approved by
Plantronics, Inc. could void the user's authority to operate
the equipment.

EXPOSURE TO RADIO FREQUENCY RADIATION

The radiated output power of this internal wireless radio is
far below the FCC radio frequency exposure limits. Never-
theless, the wireless radio shall be used as described in
the manual.

The internal wireless radio operates within guidelines
found in radio frequency safety standards and recom-
mendations, which reflect the consensus of the scientific 
community.

Plantronics therefore believes the internal wireless radio 
is safe for use by consumers. The level of energy emitted is
far less than the electromagnetic energy emitted by wire-
less devices such as mobile phones. However, the use of
wireless radios may be restricted in some situations or envi-
ronments, such as aboard airplanes. If you are unsure 
of restrictions, you are encouraged to ask for authorization
before turning on the wireless radio.

RE

PL

AC

IN

G T

HE

 A

DA

PT

ER

 B

AT

TE

RY

FIG. 6.1 

– Remove rubber caps to expose two screws.

Loosen and remove the screws on the bottom of the

adapter using a small Philips screwdriver.

FIG. 6.2 

– Lift the cover and remove the battery.

 Insert

a new battery so the (+) and (-) symbols correspond

correctly to the labels inside the battery compar

tment.

Replace the bottom cover and insert and tighten the

two screws. Be careful not to over tighten the screws.

BL

UE

TO

OT

H P

AIR

IN

G

Use these instructions only if you replace either the

headset or adapter in your system. Your M1500 

headset and adapter are already paired when you

receive them. 

See Section 7 for instructions on pairing just the head-

set to a Bluetooth enabled mobile phone.

FIG. 6.3 – PA

IRING THE HEADSET AND ADAPTER

Before beginning the pairing process, make sure the

headset is turned ON and the adapter is tur

ned OFF . 

On the headset, PUSH IN and HOLD the headset

MUTE/VOLUME dial until the INDICATOR light begins

to flash.

On the adapter, press and HOLD the blue POWER but-

ton on the adapter for 10 seconds. The INDICATOR

light will flash once after about 3 seconds—continue to

hold the POWER button for another 5-7 seconds until it

begins to flash red.

The pairing process should take about 10

seconds.

If pairing is successful, the headset will sound a tone

and both the headset and adapter INDICATOR lights

will turn of

f. 

If pairing fails, the headset INDICATOR will stop blink-

ing after 60 seconds and return to standby mode.

Also, the adapter INDICATOR will light red and then

turn of

f. Repeat the pairing process.

NOTE – The adapter must be turned OFF and the

headset must be turned ON before pairing. See

Section 5 for instructions for turning the headset and

adapter on and off.

You may also use the headset alone with a

compatible Bluetooth mobile device. 

The following instructions show how to pair

your headset to a Bluetooth mobile phone.

Before PAIRING, you will need: (1) your fully

charged headset, (2) your mobile phone user

guide; and (3) your four-digit headset passkey

(located on the passkey card included in your

M1500 package).

FIG. 7.1 – TURN ON BOTH DEVICES

To tur

n on your headset, press and HOLD the

TALK/ON-OFF button until the button lights.

See Section 5 for more details. 

Once both devices are turned on, place the

headset and phone within an arm’

s length of

each other.

FIG. 7.2 – SELECT PAIRING MODE

Following instructions in your mobile phone

user guide, select discover, or pairing, mode

from the Bluetooth options of your phone. 

On your headset, PUSH IN and HOLD the

MUTE/VOLUME key until the INDICATOR 

light begins to blink. Your headset is now 

discoverable. 

Check your mobile phone display and follow

any instructions.

FIG. 7.3 – ENTER YOUR PASSKEY

If prompted by your phone, enter your four-

digit passkey.

Some mobile phones and portable devices

will not require a passkey.

CONFIRM PA

IRING

If pairing is successful, the headset will sound

a tone and the INDICATOR light will tur

n off. 

Check your mobile phone display to see if

pairing succeeded and follow any instructions.

NOTE

– If pairing fails, the INDICATOR light

will stop flashing after 60 seconds and your

headset will return to standby without sounding

a tone.

Refer to your mobile phone user guide and

repeat the pairing process.

CHECK THE CONNECTION

Test the headset to phone pairing by making a

call. Refer to Section 5, FIG. 5.2 and your

mobile phone user guide for more details.

Customize your headset so it fits comfortably

.

FIG. 6.1

FIG. 6.2

FIG. 6.3

MAINTENANCE/TROUBLESHOOTING

What do I do if...

TH

E A

DA

PT

ER

 U

NIT

 D

OE

SN

’T

 P

LU

IN

TO

 M

Y P

HO

NE

?

Different models of phones require dif

ferent

plug styles for your adapter. Check the 

compatibility sticker on your M1500 box

and make sure the unit you purchased is

compatible with your model phone.

MY HEADSET AND ADAPTER WON’T CONNECT

OR HAVE STOPPED CONNECTING?

Tur

n both your headset and adapter of

f, 

then back on and attempt a connection by

pressing the headset TALK button. If the 

connection fails again, follow the pairing

instructions in FIG. 6.3.

I C

AN

’T

 A

NS

WE

R C

AL

LS

FR

OM

 M

Y H

EA

DS

ET

?

You must answer and end calls using your

phone keypad. 

Make sure the adapter unit is connected

securely and is compatible with your 

model phone.

BA

TT

ER

Y C

HA

RG

ES

 D

O N

OT

 L

AS

T

VE

RY

 L

ON

G?

Be sure to press the TALK button on the

headset to disconnect the adapter between

calls. While the headset is not in use, the

adapter INDICATOR light will flash green.

Also, recharge both the adapter and 

headset at the same time.

If you are not going to use the adapter 

or headset for an extended period of time,

remove the batteries according to Sections 

2 and 6.

CA

LL

ER

S D

O N

OT

 H

EA

R M

E?

Verify that the unit is not in mute mode.

I D

ON

’T

 H

EA

R C

AL

LE

RS

?

Make sure the headset and adapter have

an active connection—

both INDICATOR

lights will flash red. Tur

n up the volume using

the volume control on your headset and on

your mobile phone.

I H

EA

R S

TA

TIC

?

Make sure the adapter cord is not touching

the antenna of your phone, Position the

adapter for the best audio parfor

mance.

See Section 3.

TH

E H

EA

DS

ET

 IS

 U

NC

OM

FO

RT

AB

LE

?

Adjust the height and direction of the earloop,

both up and down, front and back, so 

pressure is not being exerted on any par

of your ear, causing you discomfor

t. 

Gently bend the angle of the flexible earloop

to conform to the shape of your ear

HO

W D

O I

 U

SE

 T

HE

 H

EA

DS

ET

 O

MY

 L

EF

T E

AR

?

See the footnote in Section 4 for detailed

instructions.

I N

EE

D M

OR

E H

EL

P.

Visit www

.plantronics.com or call

1.800.544.4660 for assistance.

3 SECONDS

PUSH IN

!

F C C N O T I C E

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference; and

2. This device must accept any interference received, includ-

ing interference that may cause undesired operation.

This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide rea-
sonable protection against harmful interference in a resi-
dential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation.

If this equipment does cause harmful interference to radio
or television reception, which can be determined by turn-
ing the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and
receiver.

Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.

MA

IN

TE

NA

NC

E H

IN

TS

 F

OR

 O

PT

IM

AL

 P

ER

FO

RM

AN

CE

Replace both the headset and adapter batteries every 12 months.

Clean the outside of the headset with a moist cloth once a month. Dirt can decrease the

efficiency of the headset.

TR

OU

BL

ES

HO

OT

IN

G

345 Encinal Street, Santa Cruz, CA 95060 (800) 544-4660  •   www.plantronics.com

62238-01

08.02

Reviews: