PNI PORTAMATIC 475 Twin Trigger 20 Owner'S Manual Download

Page: 1 / 10

“PNI is a proud Member of these Industry Associa

ons”

PO Box 1257, Wilmington, NC 28402

910-283-9791 • 800-634-9281 • Fax 910-283-6264

Home Page: www.porta-nails.com E-mail: info@porta-nails.com

OWNER’S MANUAL

PORTAMATIC® 475 Twin Trigger 20

Thin Flooring Stapler For 1/4” - 7/16” Tongue and Groove

Engineered and Solid Wood Flooring

CAUTION

- Read important safety instruc

ons AND opera

instruc

ons BEFORE opera

ng your Pneuma

c Tool.

Your new Pneuma

c Tool is capable of dependable performance

throughout its life

me. To take full advantage of these capabili

you should thoroughly understand the proper method and technique
of its opera

on. Therefore, we suggest you read this manual before

opera

ng, and that you save it for future reference.

FORM P/N 475701 (4/22/2008)

ATENT

Summary of Contents for PORTAMATIC 475 Twin Trigger 20











Search results

Summary of Contents for PORTAMATIC 475 Twin Trigger 20

Reviews:

Related manuals for PORTAMATIC 475 Twin Trigger 20

Brands by name

Popular brands

PNI PORTAMATIC 475 Twin Trigger 20, Owner'S Manual

Search results

Summary of Contents for PORTAMATIC 475 Twin Trigger 20

Reviews:

Related manuals for PORTAMATIC 475 Twin Trigger 20

Brands by name

Popular brands