background image

DOC:

.1.00 

 – September 12, 2006 

DL Lp 

Manufactured in Canada by Autostart

 

 

A U T O M A T I C   /   M A N U A L   T R A N S M I S S I O N  

R E M O T E   S T A R T E R    

 

 

User Guide 

PS-3155 

 

 
 
 
 
 

 

WARNING 

 

It is the responsibility of the vehicle operator to ensure their 
vehicle is parked in a safe and responsible manner. 

1.  a)  Manual transmission: 

When leaving the vehicle, it is 

the user’s responsibility to ensure that the gearshift lever 
is in the 

NEUTRAL

 position and the parking brake is 

engaged in order to avoid accidents upon remote starting.

 

b) Automatic transmission: 

When leaving the vehicle, it is 

the user’s responsibility to ensure that the gearshift lever is in 
“Park” in order to avoid accidents upon remote starting.

 

2.  

It is the user's responsibility to ensure that the remote starter is 

disabled or put into valet mode before servicing.

 

 
 
 

FCC USER NOTICE (U.S.A.):  

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 
conditions: (1) this device may not cause harmful interference, and (2) this device must accept 
any interference received, including interference that may cause undesired operation.  

NOTE:

 The manufacturer is not responsible for any radio or TV interference caused by 

unauthorized modifications to this equipment. Such modifications could void the user's 
authority to operate the equipment. 

Summary of Contents for PS-3155













Reviews: