Poulan Pro 545117548 Instruction Manual Download

Page: 1 / 16

WARNING:

Read and follow all Safety Rules and Operating Instructions before

using this product. Failure to do so can result in serious injury.

ADVERTENCIA:

Lea el manual de instrucciones y siga todas las advertencias e

instrucciones de seguridad. El no hacerlo puede resultar en lesiones

graves.

AVERTISSEMENT:

Lire le manuel d’instructions et bien respecter tous les avertisse-

ments et toutes les instructions de sécurité. Tout défaut de le faire

pourrait entraîner des blessures graves.

GL
IS

PAÑOL

RANÇAIS

Please do not return unit to retailer.

Por favor, no devuelva el aparato al lugar de compra.

Veuillez ne pas retourner l’outil au détaillant.

1-800-554-6723

www.poulan--pro.com

PP400E

Poulan PRO

1030 Stevens Creek Road

Augusta, GA 30907

Poulan PRO

5855 Terry Fox Way

Mississauga, Ontario L5V 3E4

545117548

8/8/06

Instruction Manual

Manual de Instrucciones

Manuel d’Instructions

Summary of Contents for 545117548

















Search results

Summary of Contents for 545117548

Reviews:

Related manuals for 545117548

Brands by name

Popular brands

Poulan Pro 545117548, Instruction Manual

Search results

Summary of Contents for 545117548

Reviews:

Related manuals for 545117548

Brands by name

Popular brands