background image

© 1/14  Power Gear   #3010001345  Rev. 0C

Installation and 

Service Manual 

Room Slideout System 

with Programmable 

Control

Introduction

SYSTEM DESCRIPTION

Your Power Gear Slideout System is a rack and pinion design operated by a 12 
Volt DC electric motor.

MAJOR COMPONENTS

· Inner rail assemblies are designed to support the room weight.
· The 12 Volt DC gearmotor will operate the room using power from the on-board

unit battery.

· Slideout systems are equipped with a manual override that allows you to extend

/ retract the room in the event of a loss of power.

· A specially designed control that gives the user full control of room movement, in

or out. The control has programmable stops that stop the motor when the room
is fully extended or retracted and the ability to detect faults for ease in
troubleshooting.

Installation

Installation & Service Manual

Room Slideout System with  

Control Box 1510000120 and 

1510000121

          1
          1

2

2-3

4
4
5
5

CONTENTS

Introduction 
Installation 
Installation Problems

 

Program Mode   
Operation Mode          
Preventative Maintenance         
Fault Diagnostics 
Troubleshooting  
Override Modes   
Wiring Diagram  

6-7

 

7

 

     

P/N 81-1291) for proper installation of rail assemblies.

  ! "$  %&'(*''**+: ; ;

installation of room locks.

Control and touchpad Installation.

 

Refer to proper wiring diagram in back of manual

*<   = >?* *=@  B; B !;
     nents from the elements and being hit but is easily accessible for service.

+<!   !  B;?(@<F   =
     in view of slideout room and have a minimum depth of 1” inside the wall.  
     Cut 2 7/8“ wide x 1 3/4” high rectangular opening in wall to mount the    

touchpad.

3. Route and attach touchpad harness to where touchpad will be mounted.

  B;B+@H!B=; !!<
4. If using room locks, route and attach room lock harness from control to

room lock.

5. Route and attach the motor and sensor harness from the control box to

the slideout room motors.

6. Route and attach the proper gauge wire from the control to the chassis

battery.

WARNING

S

!

Always keep away from the 
slide-out room and rails when 
the room is being operated.  The 
gear assembly may pinch or 
catch on loose clothing causing 
personal injury

Failure to follow these instruc-
tions could result in serious 
injury or death

Summary of Contents for 1510000120









Reviews: