background image

Deckmate 25 Free Fall 

Pontoon

 

Windlass 

Please read and save these instructions. Read carefully before attempting to assemble, install, 

operate or maintain the product described. Protect yourself and others by observing all safety 

information. Failure to comply with instructions could result in personal injury and/or property 

damage! Retain instructions for future reference.

 Operating Instructions and Replacement Parts List

Deckmate 25 Freefall Pontoon Windlass

Description

The Deckmate 25 Free Fall Pontoon Windlass assists in the launching and retrieving of a 

“mushroom” or “river” style anchor typically used on pontoon boats.

 

This windlass has the capacity to 

lift up to a fi fty pound anchor and the patented free fall feature gives it the ability to drop and set the 

anchor in a fraction of the time that it takes a traditional power down windlass. The built in light 

assists retrieving anchors and launching or retrieving the boat at night.

Unpacking

When unpacking, inspect carefully for any damage that may have occurred during transit. Make sure 

any loose fi ttings, bolts, etc.., are tightened before putting unit into service.

Caution means a hazard that  

may cause minor or moderate 

injury if the warning is 

ignored.  It also may mean a 

hazard that will only cause 

damage to property.

Warning means a hazard 

that could cause death or 

serious injury if the warning 

is ignored.

P44054 05/22

Danger means a hazard 

that will cause death or 

serious in-jury if the 

warning is ignored.

Featuring patented 

“free fall release 

system” & over-

sized davit roller 

for smooth hands 

free operation

®

General Safety Information

Throughout this manual potential safety hazards will be noted with the following terms.  

Please read and understand these terms before operating the product.

© 2022 Powerwinch

Summary of Contents for Deckmate 25 Free Fall Pontoon Windlass


















Reviews: