PR4-58E
Euro Profile Escutcheon
332
175
PR7102-TPSP
Thumb Turn Support Plate
33.50
32
58
10
48.50
25°
10
90
22.5
36
1-56-731C
Anti-Ligature Indicator Lockset
70
⁵
/
⁸”
Machine
Screws
90
70
PR6130RBD
Roller Bolt
Dead lock
M5 Bolt
from the
other side
of the door
PR4-58E
Euro Profile Escutcheon
PR4-731
Anti-ligature
Pull Handle
PR7102-TPSP
Thumb Turn
Support Plate
102
35
3
PR4-728TP
Anti-ligature Thumb Turn/Pull
Description
Roller Bolt Deadlock 103x235
Spindle Universal 44mm-63mm
Thumb Turn/Pull complete
731 Pull Handle
Escutcheon 58mm Euro
731, 90 x 332mm Radius Indicator back plate
3 x 33.50 X 79mm Thumb turn support plate
Fixings Included
Note:
The cylinder cut out is made on the external side of the door only and must not go right through the door.
Model
Spindle Length Calculation
46
Door Thickness ÷ 2 + 20mm
+3mm
56
Door Thi 11mm
+3mm
66
Door Thickness ÷ 2 + 20mm
+3mm
76
N/A
N/A
86
N/A
N/A
96
N/A
N/A
Note A :
Check exact door thickness of each door
Note B :
Turn/Pull support plate must not be recessed
deeper than the surface of the door.
PR1 Variant
Addition for
Turn/Pull
Repair Plate
46
Door Thickness Less 3mm
56
Door Thickness Less 3mm
66
Door Thickness Less 3mm
76
N/A
86
N/A
96
N/A
If Fitting
Turn/Pull
Repair Plate
Screw Length
= Door
Thickness
Turn/Pull Screw Length
Note:
Unless ordered seperatley the
cylinder is not included in this kit.
To adjust Roller Catch
projection turn screw
anti-clockwise to
increase or clockwise
to withdraw
(Max adjustment
6.5mm – 13mm)
Note: If, when fitting the pull handle, the screws make direct contact with the lock-case, please use the shorter (5/8“)
screws included in the fixing pack.
Standard Primera Products are designed for internal applications only. For external applications products plated to
“Service Condition 5” should be used.
This Turn/Pull is equipped with a screw to adjust the projection of the
spindle if required (most likely if the spindle is cut too short in error).
When cutting the spindle to the required length please make sure
that the material is cut from the end marked ‘A’ as illustrated. The 2
slots at the opposite end of the spindle are an important safety
feature and designed to sheer at 50NM to protect the lock and
ensure clinical staff maintain control of the lock at all times.
There must be at least I sheer
point between the end of the
Turn/Pull nozzle & the lockcase.
Important Spindle & Thumb Turn Information
Sheer Points
Do Not Cut Here
Lockcase
Lockcase
Door
A
Adjust the spindle projection screw
by inserting screwdriver through
the door/lockcase.
The spindle must
engage in the socket
by at least 7mm
Adjust length of spindle by
cutting with a hacksaw at this
end. It is important that the end
of the spindle is cut square.
Primer
a Limited, Unit 8 Bankfield House, 250 Bristol
Av
enue, Blackpool, FY2 0JF
t
0330 058 0988
e
sales@safehingeprimera.com
w
www
.safehingeprimera.com
Important Note: products are protected by Intellectual Property Rights including UK and Community Unregistered Design Rights, UK and Community Registered Designs and UK Patents and Patent Applications.
For further details please contact Safehinge Primera Limited.
PR4-731A
Anti-ligature Recessed Handle
42
3
PR6130RBD
Roller Bolt
Dead lock
103
80
3
63
72
14
10
60.5
33
35
68
15
58.5
10
25
235
165
30
16
