background image

Steamer

625-OS

625-525revG-EN

Printed in USA 4/06 © 2006

Operating 
Manual

Product Identification

Control Panel

External Meter Plug Inlet 

(for calibration)

Celsius/Fahrenheit and 

DOWN Arrow Button

On/Off Rocker Switch 

(left-side of unit)

RAPID STEAMER 

Logo Button

Product Buttons 

(1 thru 4)

Temperature and UP 

Arrow Button

PRINCE CASTLE 

Logo Button

START Button

LED Display

Spatula

SANITATION

LIMITED WARRANTY

This product (with the exception of the water tube, part no. 625-197S) is 
warranted to be free from defects in material and/or workmanship for a 
period of two (2) years from date of original installation, not to exceed 30 
months from date of shipment from our factory. P.C. Boards and Heater 
Assemblies are warranted for three (3) years from date of installation, not 
to exceed 42 months from date of shipment. Any component which proves 
to be faulty in material and/or workmanship will be replaced or repaired (at 
the option of Prince Castle, Inc.) without cost to the customer for parts or 
labor. This warranty covers on location service (i.e. trip charges and/or 
mileage). Travel mileage is limited to 100 miles (200 kilometers) round trip 
(one trip warranty) from an authorized service agency or its sub-service 
agency. 

This warranty is subject to the following exceptions/conditions:

Use of any non-genuine Prince Castle parts voids this warranty.

All labor shall be performed during regular work hours. Overtime 
premium will be charged to the buyer.

Damage caused by carelessness, neglect, and/or abuse (e.g., 
dropping, tampering or altering parts, equipment damaged in shipment, 
by fire, flood or an act of God) is not covered under this warranty.

TABLE OF CONTENTS

Product Identification   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

1

Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

2

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

2

Operation   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

2

Temperature Calibration  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

3

View Firmware Version  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

3

Manual Reset  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

3

Programming Product Name and Water Cycle  . . . . . . . . . . . . . . . . . . 

4

Factory Pre-Set Temperatures  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

5

Error Messages   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

5

Regulator Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

6

Programming New Water Cycle for Existing Products   . . . . . . . . . . . . 

7

Cleaning — Daily   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

9

Exploded View and Parts List  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  10

Specifications  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  11

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  12

Wiring Diagram  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13

Water Tube Cleaning and Replacement  . . . . . . . . . . . . . . . . . . . .  15, 16

355 East Kehoe Blvd. • Carol Stream, IL 60188 USA

Telephone: 630-462-8800 • Toll Free: 1-800-PCASTLE

Fax: 630-462-1460 • www.princecastle.com

Summary of Contents for 625-OS



















Reviews: