background image

 

 

Installation, Servicing and User Instructions for 
LD64 OVENS 

CAUTION: Read the instructions before using the appliance. 
 

Important Installation Information 

The installer must ensure that installation of the unit(s) is in conformity with regulations in force at the 
time. For the UK, particular attention requires to be paid to:- 

BS7671 IEE Wiring Regulations 
Electricity at Work Regulations 
Health and Safety at Work Act 
Fire Precautions Act 

The unit has been CE-marked on the basis of compliance with the Low Voltage and EMC Directives for the 
voltage stated on the data plate. 
 

WARNING: THIS APPLIANCE MUST BE EARTHED! 
 
Preventive Maintenance Contract 

In order to obtain maximum performance from the equipment, we would recommend that a 
maintenance contract be arranged with 

AFE Serviceline

. Visits may then be made at agreed intervals to 

carry out adjustments and repairs. A quotation for this service will be provided upon request. Contact 
Serviceline as detailed below:- 

Tel: 01438 363 000       Fax: 01438 369 900 

 
     WEEE Directive Registration No. WEE/DC0059TT/PRO 

At end of unit life, dispose of appliance and any replacement parts  in a safe manner, via 
a licenced waste handler. 
Units are designed to be dismantled easily and recycling of all material is encouraged 
whenever practicable. 

Falcon Foodservice Equipment 
Wallace View, Hillfoots Road, Stirling. FK9 5PY 
Tel: 01786 455 200       Fax: 01786 469 454 
e-mail: info@falconfoodservice.com                                    

 

 

    

T100321 Ref. 8

 

 
 
 
 
 
 

Summary of Contents for LD64









Reviews: