background image

70" 

MAX

75x75/100x100
200x100/200x200
300x300/400x200
400x400/600x400

ISSUED:

 APR. 2014

CAUTION:

 

DO NOT EXCEED RATED

LISTED WEIGHT CAPACITY. SERIOUS 
INJURY OR PROPERTY DAMAGE MAY 
OCCUR!

ASSEMBLY INSTRUCTIONS

Model 50-14797

50kg

(110lbs)

RATED

TV STANDS

www.mcmelectronics.com

Model 50-14797

Warranty
This device is warranted against manufactures defects for a period of 1 year from the original date of 
purchase. This warranty covers all internal components and the cost of labor to either repair or replace
the unit. This warranty covers only the unit, and does not cover connected equipment, or any loss that
may occur, regardless of cause. It will be the sole discretion of MCM Electronics to determine the
applicability of said warranty, and determination as to whether the unit will be repaired or replaced.
Questions regarding application, use, or problems with this unit should be directed to MCM Electronics
Tech Support, which can be found at www.mcmelectronics.com.

This completes the assembly steps of this stand.  

As noted earlier, it is the ultimate responsibility of the user to ensure safe and secure 
Installation of any television on this stand.  There is no guarantee that every television, 
even if within the size and weight limits specified, will be secure in every situation. 

Once installation is complete, the user must make certain the television set is secure.  
Failure to do so could result in property damage, electrical or fire hazard and personal 
injury or death, should the television fall.  Pro Signal, MCM Electronics and all retail 
dealers providing this product cannot be held liable for damages that result from improper 
or insecure installation.

Furniture including tables, dressers, entertainment centers and shelves must be tested 
to ensure stability
Televisions should be installed out of reach of small children or pets that could potentially 
pull or knock a set from its location
Connecting cables, including power cords, cable, antenna or satellite TV wires, cables 
from other components, indoor antennas and similar items should be secured and tucked
out of the way to prevent being snagged or tripped over
Televisions should not be located in direct sunlight or in locations where they can come in 
contact with rain or moisture. 

Things to remember:

In the event the user is not confident in the safety of this installation it is highly 
recommended that a qualified installation professional be contacted.

Summary of Contents for 50-14797







Reviews: