background image

1

OWNER’S OPERATION AND INSTALLATION MANUAL

COMPACT  L.P.& NATURAL

GAS VENT-FREE STOVE

      

WARNING:

 

 

If  the  information  in this

manual  is  not  followed  exactly,a     f i r e     o r
e x p l o s i o n     m a y     r e s u l t  causing  property
damage,  personal injury,  or  loss  of  life.

       

WARNING: 

  This  is  an  unvented

gas-fired heater.  It  uses  air  (oxygen)
from  the  room  in  which  it  is installed.
Provisions  for  adequate  combustion  and
ventilation  air  must be  provided.  Refer
to  Air  For Combustion  and  Ventilation
section on  page  5  of  this  manual.

T h i s     a p p l i a n c e     m a y     b e     i n s t a l l e d     i n     a n
aftermarket*,  permanently located manufactured
(mobile) home, where  not  prohibited  by  local
codes.This appliance  is  only  for  use  with  the
type  of  gas  indicated  on  the  rating  plate. This
appliance  is  not  convertible  for  use  with  other
gases.

*Aftermarket: Completion  of  sale, not  for  purpose  of  resale,
from  the  manufacturer.

QN300RYLA      QL300RYLA

QN300RYLA-W  QL300RYLA-W

TOLL-FREE NUMBER: 1-877-886-5989

Consumer : please retain these  instruction
for future use.

Do  not  store  or  use  gasoline  or  other  flammable
vapors  and  liquids  in  the  vicinity  of  this  or  any
other  appliance.

WHAT  TO  DO  IF  YOU  SMELL  GAS

 

Do  not  try  to  light  any  appliance.

 

Do    not   touch   any    electrical   switch;  do  not

       use  any  phone  in   your  building.

 

Immediately   call   your  gas  supplier  from  a

       neighbor’s   phone.   Follow   the   gas   supplier’s
       instructions.

 

If   you   cannot  reach  your  gas  supplier, call

       the  fire  department.
Installation  and  service  must  be  performed  by  a
qualified  installer, service  agency, or  local  gas
supplier.

WATER VAPOR:A BY-PRODUCT OF UNVENTED ROOM

HEATERS
Water vaporis a by-product of gas combustion.An
unvented room heater produces approximately one
(1)ounce (30)ml
 of water for every 1,000BTU’S (.3KW’S) OF gas input
per hour,Refer to papg 7.

Installer:Please leave these instructions with the
consumer.

Continental  Appliance  Inc./U.S. Office

5 Musick      4600 Highlands Parkway  S.E.

   Irvine                       Suite#  D/E

CA 92618               Smyrna  GA 30080

Nanjing PRO-COM Electric Appliance Co.,Ltd.

#6 Chuangye Road,High New Tech.Zone,

Great Bridge Road North,Nanjing,210061,China.

   

   

WARNING

 Improper   installation,

adjustment, alteration, service  or  main-
tenance can  cause  injury  or  property
damage. Refer  to  this  manual  for  correct
installation  and operational  procedures.
For  assistance  or  additional  informa-
tion  consult  a  qualified installer,  service
agency,  or  local    gas supplier.

Summary of Contents for QL300RYLA


























Reviews: