background image

GS-23K Gas Soldering Iron Kit – Auto Ignition.

 

Instruction Manual

 

Thanks for buying PRO’SKIT GS-23K Gas Soldering Iron Kit – 
Auto Ignition. Please read all instructions carefully before using 
the product. 

SPECIFICATIONS 

Iron size 

Φ

29 x 245mm 

Gas container capacity 

15ml 

Operating time 

About 90mins   
(one gas filling) 

Soldering temperature 

up to 500

 

Hot Blow temperature 

up to 600

 

Torch temperature 

up to 1300

 

APPLICATIONS 

Repair switch board, meters

TV Cable system

Soldering circuit board

Loosen rusted nut and bolts

Sensitive IC board

Jewelry 

repair

Silver 

solder

Weld 

plastics

Automotive 

Aviation service repairs

WARNING 

1.)  Keep the touch out of reach of children. 
2.)  Read directions carefully before use. 
3.)  The burn tip and other accessory tips get hot in operation. 

Do not touch the tip or accessories, or place them on 
flammable objects 

4.)    Always have a fire extinguisher or bucket of water near 

the torch work area. 

5.)  Always point away from eyes and body when igniting or 

operating. Flam is invisibles sunlight; it can cause injury if 
used with extreme. 

6.)  Under no circumstances should you attempt to repair a 

damage torch 

7.)  Do not store under direct sunlight or anywhere that will 

exceed 104

 / 40

 

8.)  Do not immerse in water. 
9.)  Make sure the adjustment knob is firmly closed and the 

flame is completely extinguished after using. 

10.) Use only in well ventilated areas. 

OPERATION 

         

Fig1 

IGNITION

1.) 

Make sure the exhaust vent is facing upward to

avoid the damage of tabletop. 

2.) Press 

the 

safety lock button

 and 

simultaneously using your thumb to pull down the 
trigger. This action will ignite the soldering iron. 

3.) Hold 

the 

ignition button

 and release the 

safety lock button

. Slide the 

continuous flame 

switch

 to right (Fig2) for a constant flame. 

 Fig2 

EXTINGUISHING (Fig2)

Slide the 

continuous flame Switch

 to left (OFF), and 

this will cut off the gas supply and extinguish the 
flame. 

HOT BLOWER

Disassemble the 

soldering tip

 by rotating the tip

counterclockwise. The assembly will now be used as
hot blower without the soldering tip. Operation will be
the same as above for the soldering iron.
(fig1.)

TORCH

Disassemble the 

soldering tip

 and 

hot blow head

with 

metal sleeve

 by rotating counterclockwise. Install

the 

metal sleeve

 back to the unit. Operation will be the

same as above for the soldering iron. (Fig2)

FLAME ADJUSTMENT 

Slide the 

adjustment lever

 toward right side to

increase the flame strength or toward left to decrease
the flame strength.
When the flame is at “+” position, the longer flames
may cause the torch to flare or extinguish. In this
situation, please move the gas adjustment lever to “-”
side for decreasing the flame strength and set up a
most efficient flame(Blue Flame).

GAS REFUEL

1.) Use only high quality butane gas.
2.) Before refilling make sure that the 

continuous

flame Switch

 at left (OFF)side. (Fig2) 

3.) Follow the directions on butane fuel can. Insert the 

tip to 

filler valve, 

using a pumping action for best 

results 

4.) After filling allow the gas to stabilize a few minutes 

before ignite. 

STORAGE

Make sure that the torch is turned off and cool, before
storing or leaving unstable.

      TROUBLE SHOOTING 

Problem 

Probable cause 

Solution 

Does not 
ignite 

1. Empty fuel
2. Gas  Pressure

too high or too
low.

1.

Refuel

2.

Slide the adjustment lever
toward right or left.

Excessive 
gas flow 

Setting too high 

Adjust gas regulator gradually 
Re-ignite the torch by gradually 
increasing the gas. 

Low gas 
pressure 

1.

Low 

fuel

2.

Cold 

fuel

1.

Refuel

2.

Hold in hands to warm up.

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com 

Summary of Contents for GS-23K

Page 1: ...the continuous flame switch to right Fig2 for a constant flame Fig2 EXTINGUISHING Fig2 Slide the continuous flame Switch to left OFF and this will cut off the gas supply and extinguish the flame HOT BLOWER Disassemble the soldering tip by rotating the tip counterclockwise The assembly will now be used as hot blower without the soldering tip Operation will be the same as above for the soldering iro...

Page 2: ...下烙鐵頭後執行上述點火的動 作即會產生熱風 火炬 逆時針方向旋轉拆下烙鐵頭 金屬套管及熱風頭後 再將金屬套管裝上後再執行上述點火的動作即會 產生火炬 火燄調整 將火燄調整開關滑往右邊會加大火燄的強度 往左 則減小火燄的強度 當火焰調整開關在 的位置 時 可能會導致較長的喇叭形火焰或熄滅 當這種 狀況發生時請將火焰調整開關滑往 側 降低火 焰的強度並調整成有效的火焰 藍色火燄 填充瓦斯 1 請使用高品質丁烷瓦斯 2 填充瓦斯前請先確認連續火燄開關已撥到左 邊 圖二 3 依照指示在將瓦司罐的填沖頭插入填寫閥 門 並且將瓦斯管罐以重覆壓入放鬆的方式進 行瓦斯填充 4 填充完成後 請將產品靜置數分鐘後再進行點 火 收納存放 收納存放或是擱置前時請確認產品為熄火並且冷 卻的狀況下進行 5 簡易問題排除 問題 可能發生的原因 解決方法 點不著火 1 沒瓦斯 2 瓦斯壓力太低 1 補充瓦斯 2 火燄調整...

Reviews: