Board
Diagram
Please
take
the
following
steps
Please
check
the
following
accessory
,
if
you
find
the
item
lost, please contact our local
dealer.
POE Splitter
1set
M
to
M
DC
power
cable
1set
User
Manual
1set
1
)
Please
turn
off
the
system
'
s
power
before
the
installation
;
2)
Connect network
cable
with
PoE Switch and connect the other cable end with the Poe IN
port;
3
)
Connect
the
IP
camera
to
POE
splitter’s ethernet port with another cable;
4) Connect Splitter
'
s
DC
port
with
the
IP
camera’s Power port with the DC cable
.
5
)
Please
examine
the
system
and
power
it;
Installation
The
product
is
a
PoE
Network and Power Splitter based on
. The device is
compatible with POE switch that based on IEEE
802
.
3af standard. The product can also
provide network and power source for network device that does not support PoE function.The
product
provide
DC
5V
/
12V
/
24V
3
Level
Power
output. It can support different power request
for IP camera or IP device.
。
IEEE
802
.
3af
Feature
PoE
Splitter
Voltage Output:
DIP
Adjustment
Available
,
available
for
various
ethernet
product
.
Support
10
/
100
/
1000
Mbps
data
conversion
.
Power
Output
:≤
15
.
4W;
Transmission Medium
:
Cat5
/
5e/
Standard: Support IEEE802.3af
Standard
;
Power
supply
support
A
(
End-Span
)
and
mode
B
(
Mid-Span
)
Protection: Excellent circuit protection, strong lighting protection and anti-interference.
DC5V/12V/24V
6 Cable;
;
PoE
Splitter
1
2
Cat5/5
e/6 N
etwor
kCab
le
Mon
itor
NVR
IP PTZ Camera
IP Camera
IP Dome Camera
Front
Back
Notice
To
make
sure
the
transmission
quality
,
please
use
standard
Cat5
/
5e
/
6
cable.
POE S
witch
Application
POE S
plitte
r
IP Camera
Ethernet
PWR
DC
1
2
3
4
5
6
Ethernet
2
PWR
DC Power Output LED,On: Power output
Off: Power not output
3
DC
DC Power output port
4
5V/12V/24V
DIP Switch, DIP level control different DC power output,
5V/12V/24V power output available
5
PWR
PoE Power Input LED, On: PoE power input
Off: PoE power not input
6
PoE IN
PoE E
thernet Input Port
Ethe
rnet
Ethe
rnet
Ethe
rnet
Ethe
rnet
DC P
owe
r
DC P
owe
r
DC P
owe
r
DC P
owe
r
5V
PWR
12V
24V
PoE IN
连 接 接 口
Specification
连 接 接 口
Item
Description
Power
Power
Electric Supply
Power Voltage
AC100V~AC240V
Output Power Rate
≤15.4W
Network
Port
Communication Port
1×RJ45 Input
TransmissionRate
10/100Mbps、10/100/1000Mbps
Transmission
Cat5/5e/6 Cable
Distance
100m(Max)
Status
Power LED
1(
Green)
PoE LED
1 (Yellow)
Protection
Surge Protection
1KV Per:IEC61000-4-5
ESD
1a
Contact Discharge Level 3
1b Air
Discharge Level 3
Environmen
t
Working
Temperature
0℃~55℃
Storage
Temperature
-20℃~70℃
Humidity
0~90%
Structure
Size
120mm×62mm×39mm
Material
ABS
Material
Color
Black
Weight
200g
Stability
MTBF
>30000
h
连 接 接 口
Problem
Examination
Please
remove the problem according to the following steps
If the device installed according to the user manual;
If the RJ45 reach the standard of EIA/TIA568A or 568B;
Please make sure the POE port power rate output does not surpass 15.4W. Also please make
sure the input network device power rate does not surpass 15.4W.
Please use a normal device to replace the failure one;
Specification change will not be noticed
3
4
Instruments to be used: wire crimper, network tester. Wire sequence of RJ45 plug should
conform with EIA/TIA568A or 568B.
1. Please remove 2cm long the insulating layer, and bar the 4 pairs UTP cable;
2. Separate the 4 pairs UTP cable and straighten them;
3. Line up the 8 pieces of cables per EIA/TIA 568A or 568B.
4. Cut off the cables to leave 1.5cm bare wire;
5. Plug 8 cables into RJ45 plug, make sure each cable is in each pin.
6. Use the wire crimper to crimp it;
7. Repeat above 5 steps to make the another end;
8. Using network tester to test the cable whether is working.
Plug Producing Method
pin
color
white
/
green
green
blue
white/orange
white
/
blue
white
/
brown
orange
brown
1
2
3
4
5
6
7
8
pin
color
1
2
3
4
5
6
7
8
white/green
green
blue
white
/
orange
white/blue
white/brown
orange
brown
EIA/TIA 568A
EIA/TIA 568B
When choose RJ-45 make sure if one end is EIA/TIA568A,the other end should also be EIA/TIA568A.
When choose RJ-45 make sure if one end is EIA/TIA568B,the other end should also be EIA/TIA568B.
Notice
POE Injector
POE Injector
To prevent fire or shock hazards, do not expose unit
to water for an extended period of time.
There are uninsulated and dangerous voltages within the enclosure of this
product. These currents may be of sufficient magnitude to cause electric shock
or death to individuals.
To reduce the risk of electric shock, please do not remove the cover or back of
this product. Only a qualified technician should tamper with the interiors of this
item and it’s electrical components.
• Avoid using this product at extreme high or low temperatures.
For more information please review product specifications.
• Never expose products to direct sunlight or other extreme
conditions, damages to your product could occur.
• Do not mount or place any products near a heater or radiator.
*Violation of any of these recommendations could result in ProVisual voiding this products warranty. Please
visit our website for all details regarding your warranty.
HIGH RISK OF ELECTROCUTION.
CAUTION:
BA401-SP
|
PoE Splitter Instruction Manual
Product Features
Plug Producing Methods
•
Voltage Output:
DC5V/12V/24V, 10/100/1000 Mbps data conversion
•
Power Output:
≤
15.4W
•
Standard:
Supports IEEE802.3af, Power supply support A (end-span)
and mode B (mid-span).
•
Protection:
Excellent circuit, lighting and anti-interference protection.
•
Structure:
Supports tablet installation. 2 sets of PoE power adapters
can be connected with a Bayonet.
1
4
Congratulations on purchasing this BA401-SP model PoE splitter. This item is
compatible will all PoE switches that are based on IEEE 802.3af standards. This
splitter can also provide data and a power source for devices that do not support
PoE functions. The BA401-SP provides 3 levels of power output, DC 5V / 12V / 24V
providing different power requests for IP devices.
NOTE:
Please read this instructional booklet carefully to ensure proper use of the
product, as well as reduce the risk of injury or death.
1. Remove 2cm of the insulating layer from the end of cable, and bar together the 4
pairs of UTP cables.
2. Separate the 4 pairs of UTP cable and straighten them.
3. Line up the 8 cables of EIA/TIA 568A or 568B.
4. Strip each cable to reveal 1.5cm of bare wire
5. Plug 8 cables into RJ45 plug, making sure that all cables make contact with pins.
6. Use a wire crimper to crimp the connection.
7. Repeat steps 1-6 to create connections as needed.
8. Use a network cable tester to assure cable is working properly before installation.
Instruments needed:
wire crimper, network cable tester.