background image

 1 

 

 

 

 

 

           7046-191C 

 

 

 

         April 30, 2015

NOTICE: DO NOT DISCARD THIS MANUAL

2700 INSERT ACC WOOD INSERT

Automatic Combustion Control (ACC)

Model(s):

27I-ACC

Owner’s Manual

Operation & Care

INSTALLER: Leave this manual with party responsible for use and operation. 
OWNER: Retain this manual for future reference. 

Contact your dealer with questions on installation, operation, or service.

 HOT 

SURFACES!

 

Glass and other surfaces are hot  

 

during operation AND cool down. 

Hot glass will cause burns.

• 

Do not touch glass until it is cooled

• 

NEVER allow children to touch glass

• 

Keep children away

• 

CAREFULLY SUPERVISE children in same room as 

fi

 replace.

• 

Alert children and adults to hazards of high temperatures

• 

High temperatures may ignite clothing or other 
fl ammable materials.

• 

Keep clothing, furniture, draperies and other 

fl

 ammable 

materials away.

 WARNING

If the information in these instruc-
tions is not followed exactly, a 
fi re may result causing property 
damage, personal injury, or death.

 

•  Do not store or use gasoline or other 

fl

 am-

mable vapors and liquids in the vicinity of 

this or any other appliance.

•  Do not over

fi

 re - If heater or chimney con-

nector glows, you are over

fi

 ring. Over

fi

 ring 

will void your warranty.

•  Comply with all minimum clearances to 

combustibles as speci

fi

 ed.  Failure to 

comply may cause house 

fi

 re.

WARNING

Fire Risk.

For use with solid wood fuel only.
Other fuels may over

fi

 re and generate 

poisonous gases (i.e. carbon monoxide).

Installation and service of this appliance should be 
performed by quali

fi

 ed personnel.  Hearth & Home 

Technologies recommends NFI certi

fi

 ed profession-

als, or technicians supervised by an NFI certi

fi

 ed 

professional.

WARNING

NOTE

To obtain a French translation of this manual, please contact 
your dealer or visit www.quadra

fi

 re.com

Pour obtenir une traduction française de ce manuel, s’il vous 
plaît contacter votre revendeur ou visitez www.quadra

fi

 re.com

O-T L

Tested and 

Listed by

Portland

Oregon USA

OMNI-Test Laboratories, Inc.

C

US

Summary of Contents for 27I-ACC

































Reviews: