background image

Quadra-Fire • Adventure-III Installation Manual • 4083-901 • Rev B • 05/15

1

Model(s):

Adventure-III

EPA CERTIFIED WOODBURNING 

APPLIANCE

 

 

HOT SURFACES!

 

 

Glass and other surfaces are hot 

 

 

during operation AND cool down.  

Hot glass will cause burns.

• 

Do not touch glass until it is cooled

• 

NEVER allow children to touch glass

• 

Keep children away

• 

CAREFULLY SUPERVISE children in same room as 

appliance.

• 

Alert children and adults to hazards of high temperatures

•  High temperatures may ignite clothing or other 

flammable materials.

• 

Keep clothing, furniture, draperies and other flammable 

materials away.

 WARNING

If the information in these instruc-

tions is not followed exactly, a 

fire could result causing property 

damage, personal injury, or death.

 

•  Do not store or use gasoline or other flamma-

ble vapors and liquids in the vicinity of this or 

any other appliance.

•  Do not overfire - If appliance or chimney con-

nector glows, you are overfiring. Overfiring 

will void your warranty.

•  Comply with all minimum clearances to com-

bustibles as specified.  Failure to comply may 

cause house fire.

Installation and service of this appliance should be 

performed by qualified personnel.  Hearth & Home 

Technologies recommends HHT Factory Trained or 

NFI Certified professionals.

WARNING

WARNING

Fire Risk.

For use with solid wood fuel only.

Other fuels may overfire and generate 

poisonous gases (i.e. carbon monoxide).

Installation Manual

Installation & Appliance Set-Up

INSTALLER: Leave this manual with party responsible for use and operation. 

OWNER: Retain this manual for future reference. 

NOTICE: DO NOT DISCARD THIS MANUAL

NOTE

To obtain a French translation of this manual, please contact 

your dealer or visit www.quadrafire.com

Pour obtenir une traduction française de ce manuel, s’il vous 

plaît contacter votre revendeur ou visitez www.quadrafire.com

Summary of Contents for Adventure-III

























Reviews: