background image

1

7060-801A

April 26, 2019

R

EXPLORER III APAC WOOD FIRE 

APPLIANCE

AUTOMATIC COMBUSTION 

CONTROL (ACC)

MODEL:

EXPIII-MBK-APAC

Installation Manual

Installation & Appliance Set-Up

INSTALLER: Leave this manual with party responsible for use and operation. 

OWNER: Retain this manual for future reference. 

NOTICE: DO NOT DISCARD THIS MANUAL

HOT SURFACES!

Glass and other surfaces are hot during 

operation AND cool down.

WARNING

Hot glass and appliance will cause burns.

•  Do not touch glass until it is cooled

•  Use leather gloves when reloading fuel

•  NEVER allow children to touch glass

•  Keep children away

•  CAREFULLY SUPERVISE children in same room 

as appliance.

•  Alert children and adults to hazards of 

high temperatures

•  High temperatures may ignite clothing or other 

flammable materials.

•  Keep clothing, furniture, draperies and other 

flammable materials away.

WARNING

Fire Risk.

For use with solid wood fuel only.

Other fuels may over fire and generate 

poisonous gases (i.e. carbon monoxide).

• 

Do not store or use gasoline or other flammable 

vapors and liquids in the vicinity of this or any 

other appliance.

• 

Do not over fire

 - If appliance or chimney connector 

glows, you are over firing. Over firing will void 

your warranty.

• 

Comply with all minimum clearances to combustibles 

as specified. Failure to comply may cause house fire.

WARNING

If the information in these instructions is 

not followed exactly, a fire could result 

causing property damage, personal injury, 

or death. 

Summary of Contents for EXPIII-MBK-APAC

























Reviews: