background image

www.quadrafi re.com

7019-221C

November 14, 2011

SANTA FE PELLET INSERT

O - T   L

Tested and 

Listed by

Portland

Oregon USA

OMNI-Test Laboratories, Inc.

C

US

Owner’s Manual

Installation and Operation

SANTAFEI-MBK

Model: 

SAVE THESE INSTRUCTIONS

NOTICE

•  Important operating and 

maintenance  instruc-
tions included.

• 

Leave  this  manual  with 
party responsible for use 
and operation.

• 

Read, understand and 
follow  these  instruc-
tions for safe installa-
tion and operation.

DO NOT

DISCARD

 WARNING

Please read this entire manual 
before installation and use of this 
pellet fuel-burning room heater.  
Failure to follow these instructions 
could result in property damage, 
bodily injury or even death.

• 

Do not store or use gasoline or other fl am-
mable vapors and liquids in the vicinity of this 
or any other appliance.

•  Do not overfi re - If any external part starts to 

glow, you are overfi ring. Reduce feed rate.  
Overfi ring will void your warranty.

•  Comply with all minimum clearances to com-

bustibles as specifi ed.  Failure to comply may 
cause house fi re.

Check building codes prior to installation.
•  Installation MUST comply with local, regional, state and national 

codes and regulations.

•  Contact  local  building  or  fi re  offi cials  about  restrictions  and 

installation inspection requirements in your area.

CAUTION

Tested and approved for wood pellets and shelled 
fi eld corn fuel only.  Burning of any other type of fuel 
voids your warranty.

CAUTION

WARNING

Hot glass will cause burns.

•  Do not touch glass until it is cooled
•  NEVER allow children to touch glass
•  Keep children away
•  CAREFULLY SUPERVISE children in same room as 

fi replace.

•  Alert  children  and  adults  to  hazards  of  high 

temperatures.

 

High  temperatures  may  ignite  clothing  or  other 
fl ammable materials.

•  Keep clothing, furniture, draperies and other fl ammable 

materials away.

HOT SURFACES!

Glass and other surfaces are 
hot during operation AND 
cool down.

Summary of Contents for SANTAFEI-MBK





















































Reviews: