background image

1

IMPORTANT:

Please note when you open the carton, carefully check the 

unit and make sure there is no damage. If you have any 

problems with assembling the unit, with how the various 

functions work or with damage or missing parts please call 

1-800-459-4409 (9:00am - 5:00pm EST) immediately for 

service. 

 

NOTE: DO NOT RETURN UNIT TO THE STORE BEFORE CALLING 

THE TOLL FREE NUMBER. Do not dispose of your cartons until 

you are completely satisfied with your new heater.

NOTE: Light bulbs may become loose during shipping. If the 

flame effect is dim or does not work, please check that the 

light bulb or bulbs are finger tight in socket. See instructions 

for replacing the bulb or bulbs.  

INSTRUCTION MANUAL

ATTENTION: 

1.  Find a location for the fireplace heater that is protected from 

direct sunlight.

2.  Do not plug the unit into the power outlet before reading all 

instructions.

SAVE THESE INSTRUCTIONS 

FOR FUTURE USE.

IMPORTANT SAFETY  

INSTRUCTIONS

WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS 

SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, 

ELECTRIC SHOCK, AND INJURY TO PERSONS, INCLUDI NG THE 

FOLLOWING:

1)   Read all instructions before using this electric fireplace heater.
2)   This electric fireplace heater is hot when in use. To avoid 

burns, do not let bare skin touch hot surfaces. The grill directly 

in front of the heater outlet becomes hot during heater opera-

tion. Keep combustible materials, such as furniture, pillows, 

bedding, papers, clothes, and curtains at least 3 feet (0.9 m) 

away from the front of the unit and keep them away from the 

sides and rear. 

3)   Extreme caution is necessary when any heater is used by, or 

near, children or individuals with disabilities and whenever the 

fireplace is left operating and unattended. 

4)   Always unplug fireplace when not in use.
 5)  Do not operate any electric fireplace with a damaged cord or 

plug or after the heater malfunctions, has been dropped or 

damaged in any manner.  

6  Do not use outdoors. 
7)   This electric fireplace heater is not intended for use in 

bathrooms, laundry areas and similar indoor locations. Never 

locate heater where it may fall into a bathtub or other water 

container. 

8)   Do not run cord under carpeting. Do not cover cord with throw 

rugs, runners, or similar coverings. Arrange cord away from 

traffic area and where it will not be tripped over. 

9)   To disconnect fireplace, turn controls to off, then remove plug 

from outlet. 

10) Connect to properly grounded outlets only.
11) Do not insert or allow foreign objects to enter any ventilation 

or exhaust opening as this may cause an electric shock or 

fire, or damage the heater. 

12) To prevent a possible fire, do not block air intakes or exhaust 

in any manner. Do not use on soft surfaces, like a bed, where 

openings may become blocked. 

13)  A heater has hot and arcing or sparking parts inside. Do not 

use it in areas where gasoline, paint, or flammable liquids are 

used or stored. 

14) Use this fireplace heater only as described in this manual. Any 

other use not recommended by the manufacturer may cause 

fire, electric shock, or injury to persons. 

15) Avoid the use of an extension cord because the extension cord 

may overheat and cause a risk of fire. However, if you have to 

use an extension cord, the cord shall be No.14 AWG minimum 

size and rated not less than 1875 watts.

16) Caution: Do not plug this product into a receptacle controlled 

by a wall switch or dimmer.

17) When storing or transporting the unit and cord, keep in a dry 

place, free from excessive vibration and store so as to avoid 

damage.

ELECTRIC FIREPLACE HEATER

MODEL: MM910-33ECN (NDF-120N)

Summary of Contents for MM910-33ECN








Reviews: