background image

 

SafeLog 100

 

Single Gas 
Datalogging Monitor

 

 

Operator's Manual

 

 

Note:

 Due to the new ATEX Directive in Europe, all 

references in this document to "Ex" or "EEx" for intrinsic 
safety approvals should be disregarded effective 7/1/03 
within the member countries of the European Union (EU). At 
this time, this product is not approved in accordance with the 
new ATEX Directive and is not sold for use in hazardous 
atmospheres or explosive zones by customers within the 
EU.  Outside of the EU, all references to intrinsic safety 
continue without change. 

 

Thank you for choosing Quest Technologies to meet your personal gas moni-
toring needs. The SafeLog 100 is an extremely rugged, lightweight single gas 
datalogging personal monitor. It is our goal to make your decision to buy Quest 
products the right one, and to provide support for any questions or concerns that 
might arise.

 

 
The purpose of this manual is to provide the user with the necessary information 
to operate the SafeLog 100. The entire manual should be read to fully 
understand the many features this instrument offers.

 

 
This manual is not all inclusive and cannot cover all unique situations. In addi-
tion, no warranties are contained in this manual except as described under the 
warranty policy section.

 

 
Copyright 1997 Revision B

 

P/N 054-479

 

 
 
 
 
 
 
 
 
 
 
 
 

 

 

1060 Corporate Center Drive • Oconomowoc, WI 53066 USA • 800-245-0779 • Fax:262-567-4047

 

http://quest-technologies.com 

Printed in U.S.A.

 

Summary of Contents for SafeLog 100


















Reviews: