background image

Radiocrafts

Embedded Wireless Solutions

   RC1xx0 / 2x00DK

 

 

 
 
 

2008 Radiocrafts AS     RC1xx0 / 2x00DK Demonstration Kit version 3.0 User Manual (rev. 3.1) 

Page 1 of 14 

 

RC1xx0 / 2x00DK Demonstration Kit User Manual

 

 

 

                               

 

Table of contents 

 

TABLE OF CONTENTS ..........................................................................................................1

 

QUICK START GUIDE ............................................................................................................2

 

INTRODUCTION .....................................................................................................................3

 

DEMONSTRATION BOARD ...................................................................................................4

 

POWER SUPPLY SECTION ...................................................................................................5

 

RS-232 INTERFACE ...............................................................................................................6

 

CONTROLLING CONFIG-MODE VIA THE RS232 PORT ......................................................6

 

CONNECTORS .......................................................................................................................7

 

PUSH BUTTONS.....................................................................................................................7

 

USING THE DEMONSTRATION KIT ......................................................................................7

 

ANTENNA SELECTION VERSUS RANGE PERFORMANCE ................................................8

 

CIRCUIT DIAGRAM ................................................................................................................9

 

BILL OF MATERIALS ...........................................................................................................10

 

PCB LAYOUT........................................................................................................................11

 

TROUBLESHOOTING...........................................................................................................13

 

DOCUMENT REVISION HISTORY .......................................................................................14

 

DISCLAIMER.........................................................................................................................14

 

TRADEMARKS .....................................................................................................................14

 

LIFE SUPPORT POLICY.......................................................................................................14

 

CONTACT INFORMATION ...................................................................................................14

 

Summary of Contents for RC1 0 Series















Reviews: