background image

RANDOM*SOURCE

 

RANDOMSOURCE.NET

1

Serge NTO

SERGE  
New Timbral Oscillator 
(NTO)

 

for Eurorack

The Serge NTO is an iconic Serge design and one of the rarest, most sought-after oscillators. To quote the 
original 1983 Serge catalog:

The Serge New Timbral Oscillator (NTO) is the 
state-of-the-art VCO, featuring exceptional 
range, superb temperature stability, and 
accurate tracking. Dynamic depth frequency 
modulation and voltage control of waveform 
allow unprecedented control over a wide range 
of sound qualities.

EXPONENTIAL 1 VOLT/OCTAVE  
RESPONSE

Exponential response parallels the response of 
human hearing perception as well as musical 
pitch structure. With multiple oscillators, each 
must respond exponentially to control voltages 
to allow transposition from key to key and to 
produce alternative equal-tempered tunings 
such as quarter and third tones. In addition, the 
one-volt-per-octave response assures that the 
New Timbral Oscillator is compatible with most 
keyboard and computer controllers.

ACCURATE TRACKING

When two or more oscillators are tuned, it is expected that they will remain in tune throughout their entire range (in other words, 
that they track). Even two oscillators which track within a fraction of a semitone will be out of tune at the extremities of their range. 
Therefore, the New Timbral Oscillators have been designed so that any two will track within one cycle/second throughout their 
entire musical range.

TEMPERATURE STABILITY

Instability of pitch with changes in temperature is the criticism of most synthesizer VCO’s. Performers are aware of the disastrous 
effects of temperature when they must desperately retune oscillators that have drifted during a live performance. The temperature 
sensitive components are kept at a static temerature by a solid-state “oven”. 

Summary of Contents for SERGE NTO








Reviews: