background image

10/05 EINS 511985

 

 

Better than you ever imagined

 

Installation & Servicing Instructions 

for Rayburn Cookmaster 300K and 

Rayburn Cookmaster Plus 308K 

Oil-Fired Cooker

  

Consumer Protection Act 1987 

As responsible manufacturers we take care to make sure that our products are designed and constructed to meet
the required safety standards when properly installed and used. 

IMPORTANT NOTICE: 

Any alteration that is not approved by Aga-Rayburn, could invalidate the approval of the

appliance, operation of the warranty and could also affect your statutory rights.

 

Control of Substances - Health and Safety Important 

This  appliance  may  contain  some  of  the  materials  that  are  indicated.  It  is  the  Users/Installers  responsibility  to
ensure  that  the  necessary  personal  protective  clothing  is  worn  whenhandling,  where  applicable,  the  pertinent
parts that contain any of the listed materials that could be interpreted as being injurious to health and safety, see
below for information. 

Firebricks, Fuel beds, Artificial Fuels - 

when handling use disposable gloves.

 

Fire Cement - 

when handling use disposable gloves.

 

Glues and Sealants - 

exercise caution - if these are still in liquid form use face mask and disposable gloves.

 

Glass  Yarn,  Mineral  Wool,  Insulation  Pads,  Ceramic  Fibre,  Kerosene/Gas  Oil  - 

may  be  harmful  if  inhaled, 

may be irritating to skin, eyes, nose and throat. When handling avoid inhaling and contact with skin or eyes. Use
disposable  gloves,  face-masks  and  eye  protection.  After  handling  wash  hands  and  other  exposed  parts.  When
disposing of the product, reduce dust with water spray, ensure that parts are securely wrapped.

 

INTRODUCTION

 

The Rayburn Cookmaster Plus 308K is a cooker providing domestic hot water and cooking facilities. It is available
with a vertical flue and outlet only, with the oil burner operating on natural draught. 

The boiler is designed for use in an open vented water system only, with gravity D.H.W. primaries. 

Page 1 of 23

EINS 511985

26/10/2006

file://\\server1\docs\NetCDs\Aga%20Product%20Information%20Spares%20and%20Tec...

Summary of Contents for Cookmaster 300K
























Reviews: