background image

AKKU

PASS

FLASH

PASS

EEPROM              PASS
RTC

PASS

CAN

PASS

FPC902
Version 2

1

7

.

1

Aug    3  2013
14:32 : 06

Service STG                       > 

FPC902

Service STG Slave             >
Flash-Programmer             >

Setup                >

Connect with STG ...

 Yes 

Accept all parameter
from the STG?

  Offline

Parameter download
from STG ...

 Continue 

STA20_UL V1.00

Break-out USA
Automatic
0 Errorless

SERVICE STG

Parameter                           >

Maintenance                        >
Functions                             >

Operation mode                   >

Connect the FPC-902 to the black 4 conductor plug located on the left side 
of the Series 5100 control. The following sequence of screens should occur.

Servicing the Series 5100(Sys.20) with the FPC-902 Hand Terminal

Jan 2014   BG

Press “OK”

Press “OK”

Press “OK”

The screen sequences on the following pages start from this point and document the various 
adjustable parameters in the control.  When at any of the screens shown below, the above 
screen can be accessed by pressing the “ESC” key one or more times.

Configure System

Learning System                 >

Service Sensor                   >

Summary of Contents for 5100 Series






















Reviews: