background image

Operating Instructions

Reelcraft Industries, Inc.  •  2842 E Business Hwy 30, Columbia City, IN 46725

Ph: 800-444-3134 / 260-248-8188  •  Fax: 800-444-4587 / 260-248-2605

Customer Service: 855-634-9109  •  reelcraft@reelcraft.com  •  www.reelcraft.com

Series WC7000 Welding Cable Reels

Model Numbers:

WC7000

WCH7000

Read this manual carefully before installing, operating or 

servicing this equipment.

IMPORTANT

Four 1/2” diameter mounting holes

Dimensions

WC7000 WCH7000

A

20 1/4”

20 1/4”

B

19 3/4”

19 3/4”

C

7 7/8”

7 7/8”

D

3 7/8”

3 7/8”

E

13 1/4”

14”

• Ensure that only a qualified electrician installs/services this 

equipment.

• Ensure that power supply voltage does not exceed maximum 

voltage rating of reel.

• Ensure that reel is properly installed before connecting to power 

supply.

• Ensure that all electrical power is removed from reel before ser-

vicing.

• Check for frayed/broken wires before each use.

• Pull electrical cord from reel by grasping the electrical cord 

itself, not the work device.

• If an electrical malfunction should occur, remove power from reel 

immediately.

• Ensure that reel, electrical cable, and equipment being serviced 

are properly grounded. Use an ohmmeter to check ground 

 continuity.

• If reel ceases to unwind or rewind, remove power immediately.  

Do not pull or jerk on electrical cable!

• Treat and respect the cable reel as any other piece of machinery, 

observing all common safety practices.

WARNING:

 Even low voltage can cause irreparable damage or 

death! Exercise extreme caution while operating or servicing this 
equipment.

WARNING:

 This reel is to be used for cable storage only! The 

entire length of cable must be unwound before use. Severe dam-
age to the reel will result if the cable is energized while fully 
wound on the reel.

SAFETY

Personal injury and/or equipment damage may result if proper safety 
precautions are not observed.

Form# 1154-304  Rev: 10/2018

Summary of Contents for WC7000










Reviews: