8
7
9
2 YEAR
WARRANTY
R5150AU
Use and Care Instruction Manual
PLEASE READ PRIOR TO USE
■
Cover the shaver heads with the protective head guard between uses. When
removing the head guard or placing it back onto the shaver, do not apply
pressure to the floating cutter surfaces, as you damage them.
■
Never submerge the shaver completely under water.
H
I
J
K
L
M
N
O
P
Q
R
S
T
Daily:
1.
Press the release button on front of shaver and open head assembly. (Diagram H)
2.
Tap out excess hair shavings. (Diagram I)
3.
Rinse the head of the shaver in running water.
NEVER
submerge the shaver in water!
4.
Close head assembly. (Diagram J)
Replacing Your Heads & Cutters
Monthly:
1.
Perform the daily cleaning steps 1 and 2.
2.
Remove the cover from the hair pocket assembly. (Diagram K) Place the body of
the shaver aside to ensure that it will not get wet.
3.
Place a drop of liquid soap on each cutter. (Diagram L)
4.
Brush the soap around vigorously using the supplied cleaning brush. (Diagram M)
5.
Release the inner cutter carrier by rotating the locking arms counter-clockwise.
(Diagram N)
6.
Remove the inner cutter carrier away from the cutters. (Diagram O)
7.
Remove the cutters. (Diagram P)
8.
Thoroughly brush any hair off of the inner and outer cutters (Diagram Q) and
rinse away any soap and debris from inner and outer cutters. (Diagram R)
9.
Replace the inner cutters. (Diagram S)
10
. Place the inner cutter carrier back into position and lock into place by rotating
the locking arms clockwise until they snap into place. (Diagram T)
11
. Lubricate each cutter with household oil.
12
. Close the head assembly. (Diagram J)
** Trimmer:
Lubricate teeth with oil every six months
Lubricate
Remington® Shaver Saver (SP-4) lubricates and cleans your shaver’s cutters and
head assembly. The lubricant helps remove hair clippings while reducing wear.
Spray on the heads and cutters after each shave to keep your shaver operating at
peak performance.
Please refer to the shaver comparison and features chart near the front of
this manual that lists the correct replacement part number for your shaver.
It is very important to replace your head and cutters when necessary to ensure
a close, comfortable shave without irritation. We recommend they be replaced
every 6 months. Here are some signs of head and cutter wear, indicating that
replacement is needed:
■
Irritation: As the heads get excessively worn you may experience some skin
irritation. This would be especially noticeable when you apply moisturizing lotion.
■
Pulling: When the cutters wear you may feel a sense of pulling and a loss of
closeness when you shave. This is an indication that it is time to replace your
heads and cutters.
IMPORTANT SAFETY
INSTRUCTIONS
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW
THESE INSTRUCTIONS:
When using an electrical appliance, basic precautions should always be observed,
including the following.
Read all instructions before using this shaver.
■
Do not reach for an appliance that has fallen into water. Unplug it immediately.
■
Use only when the shaver is in dry condition.
■
Do not submerge in water.
■
An appliance should never be left unattended when it’s plugged in, except when
charging a rechargeable appliance.
■
Close supervision is necessary when this appliance is used by, on, or near
children, or individuals with certain disabilities or special needs.
■
Use this appliance only for its intended use as described in this manual. Do not
use attachments not recommended by the manufacturer.
■
Never operate this appliance if it has a damaged cord or plug or if it is not
working properly, if it has been dropped or damaged, or if it has been dropped
into water.
■
Keep the cord away from heated surfaces.
■
Never drop or insert any object into any of the appliance’s openings.
■
Household use only.
■
Do not use outdoors or operate where aerosol (spray) products are being used
or where oxygen is being administered.
■
Do not plug or unplug this appliance when your hands are wet.
■
Do not wrap the cord around the appliance.
■
Always store this appliance and cord in a moisture-free area. Do not store it in
temperatures exceeding 140°F (60°C).
■
Do not use this appliance with a damaged or broken head or cutters, as facial
injury may occur.
■
Shavers, including the trimmer, are for use on facial hair only. They should not
be used for shaving the hair on your head or any other part of your body.
Remington strongly recommends that an approved Safety Switch (residual
current device) be installed to protect all bathroom power outlets. Ask an
electrical contractor for advice.
SAVE THESE INSTRUCTIONS
This product is not suitable for use in a bath or shower.
Money Back Offer - Australia/New Zealand Only
If within 30 days you are not fully satisfied with your Remington® shaver, just
return the shaver with this completed coupon and a copy of your Australian/New
Zealand purchase receipt to Remington®. In return, we will send you a cheque
for the full purchase price of the shaver. Please allow 6-8 weeks for your cheque
to arrive.
Name:
Address:
City:
State:
Postcode:
This product conforms to radio frequency interference requirements.
Warranty information can be found in the enclosed warranty card.
Any product purchased and used commercially carries a limited 90 Day Warranty
® Registered Trade Mark of Spectrum Brands, Inc., or one of its subsidiaries.
©SBI 2011
www.remington-products.com.au
REMINGTON SERVICE HOT LINE
Australia 1800 623 118 (toll free)
New Zealand 0800 736 776 (toll free)
Remington Products Australia Pty Ltd.
Remington Products New Zealand Ltd
Chifley Business Park,
Building C, Ground Floor,
1 Chifley Drive,
600 Great South Road,
Mentone, Victoria. 3194
Greenlane, 1051, Auckland,
Australia.
New Zealand
Part No T22-31679
REV 03/11
