1/6
TX341 Remote Electronic Ignition and Control System
OPERATING INSTRUCTIONS
-
FOR OEM USE ONLY
Fire or explosion hazard. Attempted disassembly or repair
of controls can cause property damage, severe injury or
death. Do not disassemble the gas valve; it contains no ser-
viceable components.
Read these instructions carefully. Failure to follow them
could result in a fire or explosion causing property dam-
age, personal injury, or loss of life. The product must be installed
and operated according to all local regulations.
A.
●
Do not light any appliance.
●
Do not touch any electrical switch; do not use any
phone in your building.
●
●
If you cannot reach the gas supplier, call the fire de-
partment.
B.
Use only your hand to push in or turn the gas control
knobs. Never use tools. If a knob will not push in or turn
by hand, don
’
t try to repair it, call a qualified service tech-
nician. Force or attempted repair may result in a fire or
explosion.
C.
Do not use this control or any gas appliance if any part has
been under water or in contact with water. Immediately call
a qualified service technician to replace the control sys-
tem and any gas control system which has been under
water or in contact with water.
D.
These instructions are to be referenced as a user guide,
and do not supersede appliance manufacturer
’
s lighting
instructions.
APPLICATION
TX341 is a battery
-
powered electronic remote ignition and
control system for gas appliances with pilot burners and ODS
systems.
GENERAL NOTES
TX341
IPI
-
8000
Radio frequency Remote
434 MHz for Europe, US, Canada;
⚠
WARNING
NOTE:
This device complies with part 15 of the FCC Rules. Oper-
ation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) This device must
accept any interference received, including interference that may
cause undesired operation. Changes or modifications not ex-
pressly approved by the party responsible for compliance could
void the user
’
s authority to operate the equipment.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency ener-
gy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful in-
terference to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is encour-
aged to try to correct the interference by one or more of the follow-
ing measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for
help.
NOTE:
This device complies with CAN ICES
-
3 (B)/NMB
-
3(B)
◆
This product meets the applicable Innovation, Science and
Economic Development Canada technical specifications.
Ce produit repond aux specifications techniques applicables a
l'innovation, Science et Developpement economique Canada.
◆
Canadian Compliance Statement
This device complies with Industry Canada license
-
exempt
RSSs. Operation is subject to the following two conditions:
1) This device may not cause interference, and
2) This device must accept any interference, including
interference that may cause undesired operation of the
device.
Le present appareil est conforme aux CNR d
’
Industrie Canada
applicables aux appareils radio exempts de licence. L
’
exploita-
tion est autorisee aux deux conditions suivantes :
1) l
’
appareil ne doit pas produire de brouillage
;
2) l
’
utilisateur de l
’
appareil doit accepter tout brouillage
radioelectrique subi, meme si le brouillage est suscepti-
ble d
’
en compromettre le fonctionnement.
Batteries
-
Remote Handset:
3 x1.5V
“
AAA
”
(quality alkaline recommended)
4.5V 100mA
Batteries
-
Receiver:
4 x 1.5V
“
AA
”
(quality alkaline recommended)
6.0V 1500mA
An AC Mains Adapter may be used instead of batteries
(only the Grand Mate or an AC Mains Adapter approved by
Grand Mate can be used).
NOTE:
These remote handsets, receiver, wall switches, are
not
interchangeable with previous versions.
For all lighting/ignition instructions please refer to appliance
manufacturer
’
s instructions.
